EverFocus Camcorder EQH5000 User Manual

HD CCTV  
Digital Video Camera  
OPERATION MANUAL  
EQH5000  
Before attempting to connect or operate, please read and follow these instructions.  
 
1. CAUTIONS  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions;  
1. This device may not cause harmful interference.  
2. This device must accept any interference received,  
including interference that may cause undesired operation.  
Note  
This equipment has been tested and found to comply with the limits for a Class A digital  
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference when the equipment is operated  
in a commercial environment. This equipment generates, uses, and can radiate radio  
frequency energy and, if not installed and used in accordance with the instruction  
manual, may cause harmful interference to radio communications. Operation of this  
equipment in a residential area is likely to cause harmful interference in which case the  
user will be required to correct the interference at his own expense.”  
WARNING  
This is a class A product. In a domestic environment this product may cause radio  
interference in which case the user may be required to take adequate measures.  
Caution  
Any changes or modifications in construction of this device which are not expressly  
approved by the party responsible for compliance could void the user’s authority to  
operate the equipment.  
1. A regulated DC12V 1A power supply is recommended for use with this camera  
for the best picture and the most stable operation.  
An unregulated power supply can cause damage to the camera.  
If an unregulated power supply is used, product warranty will be Void.  
2. It is recommended that the camera is used with a system that has an HDCCTV quality  
75 video impedance level.  
3. Do not attempt to disassemble the camera to gain access to the internal components.  
Refer servicing to your dealer.  
4. Never face the camera towards the sun or any bright or reflective light, which may  
cause smear on the picture and possible damage to the CCD.  
5. Do not remove the serial number sticker.  
6. Do not expose the camera to rain or other type of liquid.  
4
 
1. CAUTIONS  
Correct Disposal of This Product  
(Waste Electrical & Electronic Equipment)  
(Applicable in the European Union and other European countries with  
separate collection systems)  
This marking shown on the product or its literature, indicate that it should not  
be disposed with other household wastes at the end of its working life. To  
prevent possible harm to the environment or human health from uncontrolled  
waste disposal, please separate this from other types of wastes and recycle it  
responsibly to promote the sustainable reuse of material resources.  
This product should not be mixed with other commercial wastes purchased this  
product, or their local government office, for details of where and how they can  
take item for environmentally safe recycling.  
Business users should contact their supplier and check the terms and  
conditions of the purchase contract.  
Household users should contact either the retailer where they for disposal.  
5
 
2. FEATURES  
High Resolution  
1/3˝ SONY Progressive Color CMOS Sensor,  
1280x720 30fps  
• Supports Various Digital Video Output  
720p 30, 720p 60  
720p 25, 720p 50  
• Video Outputs  
Primary HD-SDI (BNC)  
Test/Setup TV Out (BNC), NTSC /PAL selectable  
• S/N Ratio : Max 50dB  
• OSD menu for setup and configuration  
• Lens Control  
Manual Iris  
DC Iris  
• Provides True Day/Night Capability with Motorized IR Cut Filter  
Adapter included for C-Mount Lens  
• Accepts CS Mount Lenses :  
DC 12V  
• Power Source :  
6
 
3. EQUIPMENT AND ACCESSORIES  
HD CCTV  
Digital Video Camera  
C-MOUNT ADAPTOR RING  
OPERATION MANUAL  
TERMINAL BLOCK  
NOTE  
PLEASE REMOVE PROTECTION FILM  
*
7
 
4. CAMERA COMPONENT DESCRIPTIONS  
• FRONT  
MOUNTING HOLE(1/4"-20 UNC)  
AUTO IRIS JACK  
C-MOUNT  
ADAPTOR RING  
(Optional - use for C-Mount lens only)  
BACK FOCUS CONTROL LEVER  
MOUNTING HOLE(1/4"-20 UNC)  
8
 
4. CAMERA COMPONENT DESCRIPTIONS  
• BACK  
. MENU SET BUTTON  
MENU NAVIGATION BUTTONS  
. UP BUTTON  
. DOWN BUTTON  
. LEFT BUTTON  
. RIGHT BUTTON  
. POWER LED  
. SDI OUT BNC  
. VIDEO OUT BNC  
. MIC IN JACK(Future Feature)  
. AUDIO OUT JACK(Future Feature)  
. TERMINAL (POWER, Digital Input/Output) “Note : Digital input and Output for Future use”  
9
 
5. INSTALLATION  
• LENS CONNECTION  
Mega Pixel Lenses are sold separately. Lenses such as a DC auto iris lens,  
CS-Mount lens and C-Mount lens can be used ( adapter included for C-Mount Lens).  
NOTE  
• Please keep the lens clean.  
• Any foreign objects and Finger marks on the lens can cause  
inferior image quality in low light level conditions.  
After attaching the lens to the camera please insert the connection plug from the DC  
auto iris lens cable into the auto lens connector, which is located on the side of the  
camera  
*NOTE  
When using a CS Mount Lens, you can attach it directly to camera,  
If useing a C Mount lens, you must attach the ring spacer provided,  
otherwise it will crack the image sensor.  
C-mount lens : 10mm or less  
CS-mount lens : 5mm or less  
10  
 
5. INSTALLATION  
Installation of C-Mount Lens  
C to CS-MOUNT ADAPTOR RING  
Lens  
Installation of CS-Mount Lens  
Lens  
11  
 
5. INSTALLATION  
• CONNECTION  
TO HD SDI IN  
HDCCTV DVR  
OR OTHER  
HDCCTV SIGNAL  
EQUIPMENT  
BNC FEMALE  
VIDEO  
HANDHELD  
TO VIDEO IN  
DC12V REGULATED  
POWER SUPPLY  
12  
 
6. DIMENSIONS  
Unit: mm(inch)  
MOUNTING HOLE  
(1/4"-20 UNC, Depth 5)  
145(5.71) / (C-Mount)  
72.58(2.86)  
138.55(5.45) / (CS-Mount)  
AUTO IRIS JACK  
C-MOUNT ADAPTOR RING  
(Optional use for C-Mount Lenses only)  
MOUNTING HOLE  
13  
 
7. SPECIFICATION  
1/3” SONY Mega-Pixel Color Progressive CMOS  
Image Device  
Effective Pixels  
Unit cell size  
1329 (H) x 1049 (V) 30fps  
3.63um (H) x 3.63um (V)  
HDCCTV : 720p 30, 720p 60, 720p 25, 720p 50  
TV Out : NTSC / PAL selectable  
Video output mode  
More than 800 TV Lines  
1.0 Lux  
H.Resolution  
Minimum illumination  
S/N Ratio  
Max 50dB  
Auto  
110.86us (1/9020 sec)  
60Hz(50Hz) selectable  
IR Cut /Pass Filter change  
ATW Push Manual  
/
Manual selectable  
Shutter speed  
Min. Exposure Time  
Flickerless  
Off  
/
True Day/Night  
White Balance  
BLC  
/
/
On/Off (by OSD)  
Manual Iris, DC Iris  
Yes  
Lens Control  
OSD Menu  
DC 12V  
Power  
Max 500mA  
Consumption  
Dimension (W x H x D)  
Weight (g / lb)  
Lens Mount  
72.5mm  
x
66mm  
x
138.5mm  
410g  
/
2.86inch  
0.90lb  
x
2.60inch  
x
5.45inch  
/
CS/C-mount  
CE, FCC  
Conformity  
Temperature/Humidity  
(non-condensing)  
Operation  
:
Celsius -10~50 (Fahrenheit 14~122)  
/
20~80%  
Storage :Celsius -20~70 (Fahrenheit -4~158)  
/
20~95%  
Specifications and designs are subject to change without notice for improving the functionality of this product.  
14  
 
8. DIGITAL INPUT/OUTPUT  
• Digital Input Port (Future Feature, Use for CDS Mode Only)  
Day and Night  
CAMERA  
CDS MODE  
A/D Port  
10bit resolution,  
Vtop 3.3V, Vbot  
MicroController  
EXTERNAL DEVICE  
DI  
=
=
0V  
Sensor Input  
(0~3.3V)  
R:1.5K  
GPIN PORT  
(3.3V)  
Digital Input Port  
External CDS is only active when day and night mode is set to EXT Mode in the OSD.  
CDS : External device to control day and night status  
• Digital Output Port ( Future Feature)  
CAMERA  
EXTERNAL DEVICE  
3.3V  
MicroController  
GPOUT PORT  
(3.3V)  
DO  
Photo  
Coupler  
R:270  
Digital Output  
(0/3.3V)  
R:10K  
Digital Output Port  
15  
 
9. OSD MANUAL  
• Menu structure  
- Main Menu  
VIDEO OUT  
LENS  
EXPOSURE  
WHITE BALANCE  
DAY / NIGHT  
IMAGE  
SPECIAL  
- VIDEO OUT Menu  
720p 30Hz / 720p 60Hz  
720p 25Hz / 720p 50Hz  
VIDEO OUT  
SDI FORMAT  
TV OUT FORMAT  
NTSC / PAL  
16  
 
8. OSD MANUAL  
- LENS Menu  
LENS  
LENS TYPE  
DC IRIS / MANUAL IRIS  
DC IRIS  
BRIGHTNESS  
IRIS SPD  
0 ~ 127  
0 ~ 112  
- EXPOSURE Menu  
EXPOSURE  
BRIGHTNESS  
0 ~ 127  
AUTO / MANUAL  
/ FLK 60Hz(FLK 50Hz)  
SHUTTER  
MODE  
MANUAL  
0~215  
SHUT LEVEL(Shutter Level)  
AGC MAX  
BLC  
0 ~ 150  
ON / OFF  
17  
 
9. OSD MANUAL  
- WHITE BALANCE Menu  
WHITE BALANCE  
MODE  
ATW / PUSH / MANUAL  
MANUAL  
R GAIN  
B GAIN  
0 ~ 255  
0 ~ 255  
- DAY / NIGHT Menu  
DAY / NIGHT  
MODE  
COLOR / AUTO / EXT / BW  
AUTO / EXT  
DAY LEVEL  
0 ~ 127  
0 ~ 127  
NIGHT LEVEL  
- IMAGE Menu  
IMAGE  
SHARPNESS  
IMAGE FLIP  
0 ~ 15  
OFF, H FLIP, V FLIP, H/V FLIP  
DNR  
OFF, LOW, MID, HIGH  
GAMMA  
OFF, 1.0, 1.8, 2.2, 2.6  
18  
 
9. OSD MANUAL  
- SPECIAL Menu  
SPECIAL  
SYSTEM INFO  
USER SET  
SAVE USER SET  
LOAD USER SET  
CLEAR USER SET  
FACTORY RESET  
CAMERA RESET  
RS485 Address  
COMM/GPIO SET  
0~255  
GP IN Status  
GP OUT Control  
LOW / HIGH  
FOCUS MODE  
ON / OFF  
LANGUAGE  
19  
 
9. OSD MANUAL  
• ICONS  
-
-
-
: Value adjustment(use LEFT/RIGHT button).  
: Select Sub Menu(use SET button).  
: Execution command(use SET button).  
-
-
: Return to previous menu.  
: Menu OFF.  
-
: Information.  
The [SETUP] menu will show up when you push the SET button.  
• Main Menu  
[ SETUP ]  
VIDEO OUT  
LENS  
720p 60Hz  
DC IRIS  
EXPOSURE  
WHITE BALANCE  
DAY / NIGHT  
IMAGE  
AUTO  
AUTO  
SPECIAL  
EXIT  
SAVE & EXIT  
- VIDEO OUT : Select SDI Out format and TV Out format.  
- LENS : Select the IRIS TYPE and adjust IRIS control value.  
- EXPOSURE : Adjust Exposure control.  
- WHITE BALANCE : Adjust White balance control.  
- DAY / NIGHT : Day / Night control.  
- IMAGE : Apply Image processing effects.  
- SPECIAL : System setting, IO setting, USER SET setting  
- EXIT : Close OSD Menu.  
- SAVE & EXIT : Save and Close OSD Menu. These settings are  
loaded and applied automatically when the Camera  
is power on.  
20  
 
9. OSD MANUAL  
Video Out  
[ VIDEO OUT ]  
- SDI Format  
Select SDI output Formats – 720p 30Hz,  
720p 60Hz, 720p 25Hz and 720p 50Hz.  
720p 60Hz  
NTSC  
SDI  
FORMAT  
TV OUT FORMAT  
- TV Out Format  
Select NTSC / PAL.  
Note : NTSC or PAL Video Format can be  
selected by pressing the RIGHT Button even  
when the OSD Menu is turned off  
ESC  
EXIT  
SAVE & EXIT  
- ESC  
Back to the previous.  
LENS  
- LENS TYPE  
Using Left / Right button, Select DC IRIS or  
[ LENS ]  
DC IRIS  
123  
1
MANUAL IRIS.  
- BRIGHTNESS  
This menu appeared on screen when DC IRIS  
LENS TYPE  
BRIGHTNESS  
IRIS SPD  
is selected.  
Using Left / Right button, adjust Brightness  
value.  
- IRIS SPD  
ESC  
EXIT  
SAVE & EXIT  
This menu appears on screen when DC IRIS  
is selected.  
Using Left / Right button, adjust Iris speed  
value.  
21  
 
9. OSD MANUAL  
EXPOSURE  
[ EXPOSURE ]  
- BRIGHTNESS  
Same as the BRIGHTNESS value in LENS  
Menu. Using Left / Right button, adjust  
Brightness value.  
123  
AUTO  
10  
BRIGHTNESS  
SHUTTER  
AGC MAX  
BLC  
OFF  
- SHUTTER  
Using Set button, go to the SHUTTER sub  
menu.  
- AGC MAX  
Using Left / Right button, adjust AGC Max  
value.  
- BLC  
ESC  
EXIT  
SAVE & EXIT  
Using Left / Right button, select on/off of Back-  
Light Compensation Control.  
SHUTTER (Sub Menu)  
- MODE  
Using Left / Right button, select Shutter Control  
[ SHUTTER ]  
modes – AUTO, MANUAL and FLK 60Hz  
(FLK 50Hz).  
MANUAL  
1
MODE  
SHUT LEVEL  
AUTO  
MANUAL  
Auto Exposure mode  
Manual Exposure mode  
ESC  
FLK 60Hz (FLK 50Hz) Flickerless mode (Default)  
EXIT  
SAVE & EXIT  
- SHUT LEVEL (Shutter Level)  
This menu can be accessed when the Shutter Speed is set to MANUAL.  
Use the Left / Right button to adjust the shutter speed control level.  
Instead of using the default conventional shutter speed of 1/60,  
you may choose other speeds. The speeds corresponding to the value of shutter  
level are listed below.  
Shutter  
Speed  
1/50 1/60 1/100 1/120 1/250 1/500 1/700 1/  
1000  
32  
1/  
1600 2500 5000 7000 10000  
20 12  
1/  
1/  
1/  
1/  
Level  
178  
169  
142  
135  
105  
65  
46  
6
4
3
22  
 
9. OSD MANUAL  
WHITE BALANCE  
[ WHITE BALANCE ]  
MANUAL  
100  
MODE  
R GAIN  
B GAIN  
100  
ESC  
EXIT  
SAVE & EXIT  
- MODE  
Using Left / Right button, select White balance modes – ATW, PUSH  
and MANUAL.  
ATW  
Auto Trace White Balance mode  
PUSH  
White Balance Push Lock mode (Auto White Balance Control & Lock)  
Manual White Balance mode  
MANUAL  
- R GAIN  
This menu appears on screen when MANUAL is selected.  
Using Left / Right button, adjust Red Gain.  
-B GAIN  
This menu appears on screen when MANUAL is selected.  
Using Left / Right button, adjust Blue Gain.  
* NOTE  
R GAIN and B GAIN is correlated with the G GAIN internally, so the R GAIN and B  
GAIN may increase or decrease with the other color gain.  
23  
 
9. OSD MANUAL  
• Day / Night  
[ DAY / NIGHT ]  
AUTO  
MODE  
DAY LEVEL  
NIGHT LEVEL  
50  
100  
ESC  
EXIT  
SAVE & EXIT  
- MODE  
Using Left / Right button, select TDN(True Day & Night) modes – AUTO,  
EXT, COLOR, and BW.  
AUTO  
EXT  
Controlled by AGC level in the processor. (AGC Type)  
Controlled by signal from CDS sensor. (CDS Type)  
Fixed Day State. Color Image.  
COLOR  
BW  
Fixed Night State. BW Image.  
- DAY/Night Levels  
This menu can be displayed by selecting AUTO or EXT in the MODE Menu.  
The Day Level and Night Level thresholds function independently from each other.  
- DAY LEVEL  
The threshold of change from B&W Mode to Color Mode can be adjusted with values  
between 0 - 127. A lower value will prevent the camera from switching to Color until  
the scene becomes brighter.  
- NIGHT LEVEL  
The threshold of change from Color Mode to B&W Mode can be adjusted with values  
between 0 - 127. A higher value will prevent the camera from switching to B&W until  
the scene becomes darker.  
Note: These is a built in offset between the Day and Night Level to prevent a  
switching level conflict. The effective Day level can not be set lower than  
the Night level  
24  
 
9. OSD MANUAL  
• IMAGE  
[ IMAGE ]  
0
OFF  
OFF  
1.0  
SHARPNESS  
IMAGE FILP  
DNR  
GAMMA  
ESC  
EXIT  
SAVE & EXIT  
- SHARPNESS: Using Left / Right button, adjust sharpness value.  
- IMAGE FLIP: Using Left / Right button, select Flip modes – OFF, H FLIP, V FLIP and H/V FLIP.  
- DNR: Using Left / Right button, select Digital Noise Reduction Modes - OFF, LOW, MID, HIGH.  
- GAMMA: Using Left / Right button, adjust gamma control setting.  
• SPECIAL  
[ SPECIAL ]  
SYSTEM INFO  
[X]  
ADDR 0  
OFF  
USER SET  
COMM / GPIO SET  
FOCUS MODE  
LANGUAGE  
ENGLISH  
ESC  
EXIT  
SAVE & EXIT  
- SYSTEM INFO  
Display Camera Version, SDI IF F/W Version &  
other information.  
[ SYSTEM ]  
HD-SDI CAMERA  
00_0000  
02.02_0000R05  
01.00_1110R00  
TYPE  
MODULE ID  
CAMERA VER  
IF F/W VER  
ESC  
EXIT  
25  
 
9. OSD MANUAL  
- USER SET  
Using Set button, display [USER SET] sub menu.  
- COMM/GPIO SET  
Using Set button, display [COMM/GPIO SET] sub menu.  
- FOCUS MODE  
In focus mode, the iris becomes fully open, electronic shutter controls the light  
level, and the TV out screen zooms into the center in order to make focusing  
easier. When in Focus Mode, the OSD Menu is not displayed. The OSD Menu can  
be toggled on and off using the Left / Right button.  
> TV Out Image  
FOCUS MODE OFF  
FOCUS MODE ON  
- LANGUAGE  
Select OSD Language. (Only English is available, currently)  
• USER SET (Sub Menu)  
- SAVE USER SET  
Saves a copy of the current configuration set by the user into  
[ USER SET ]  
a separate memory area. If user set data has been saved,  
an [O] mark is displayed and if not, an [X] mark is displayed.  
User Set settings can NOT be loaded automatically when  
the camera is powered on. They can only be loaded  
manually via the “LOAD USER SET” OSD choice. To make  
the values in a User Set become the configuration loaded  
when the camera is powered on, first load that User set,  
then choose “SAVE AND EXIT” in any of the OSD Screens;  
the current User Set OSD Settings will be written to the  
power on configuration. These steps effectively copy a User  
Set to the power on configuration.  
SAVE USER SET  
LOAD USER SET  
CLEAR USER SET  
[X]  
FACTORY RESET  
CAMERA RESET  
ESC  
EXIT  
- LOAD USER SET  
Load the saved user set, and applies to Camera.  
- CLEAR USER SET  
Clear all saved user set.  
- FACTORY RESET  
Clear all setting and initialize to factory setting.  
Clear user set.  
- CAMERA RESET  
Reboot the Camera.  
26  
 
9. OSD MANUAL  
• COMM/GPIO SET (Sub Menu)  
[ COM / GPIO SET ]  
RS485 Address (Future Feature)  
GP IN  
Status  
LOW  
LOW  
GP OUT Control  
ESC  
EXIT  
SAVE & EXIT  
- RS485 Address  
Future Feature.  
- GP IN Status ( CDS Mode Only Digital input Future Feature)  
If the OSD is set to the EXT mode in the [DAY/NIGHT] menu, this port is used to  
connect to a photo-sensor.  
- GP OUT Control (Future Feature).  
For control of an external device by the camera.  
27  
 
EverFocus Electronics Corp.  
Corporate Headquarters:  
12F, No.79 Sec. 1 Shin-Tai Wu Road,  
Hsi-Chih, Taipei, Taiwan  
China Office:  
Room 609, Technology Trade Building,  
Shangdi Information Industry Base,  
Haidian District, Beijing, China 100085  
TEL: +86-10-62973336~39  
FAX: +86-10-62971423  
TEL: +886-2-26982334  
FAX: +886-2-26982380  
U.S.A - California Office:  
1801 Highland Avenue Units A & B  
Duarte, CA 91010  
U.S.A - New York Office:  
415 Oser Avenue Unit S  
Happauge, NY 11788  
TEL: +1-631-436-5070  
FAX: +1-631-436-5027  
TEL: +1-626-844-8888  
FAX: +1-626-844-8838  
Europe - Germany Office:  
Albert-Einstein-Strasse 1,  
D-46446 Emmerich, Germany  
TEL: +49-2822-93940  
FAX: +49-2822-939495  
Japan Office:  
5F Kinshicho city Building,  
2-13-4 Koto-Bashi,  
Sumida-Ku, Tokyo, 130-0022 Japan  
TEL: +81-3-5625-8188  
FAX: +81-3-5625-8189  
India Office:  
UK Office:  
Suite 803, Housefin Bhavan, C-21,  
Bandra Kurla Complex, Bandra (East),  
Mumbai 400051. India.  
TEL: +91-222-444-8791  
FAX: +91-222-444-8790  
Unit 12 Spitfire Business Park  
Hawker Road  
Croydon, CR0 4WD  
London: 0845 430 9999  
Telford: 0845 430 8888  
Fax: 020 8649 9907  
Ihr EverFocus Produkt wurde  
entwickelt und hergestellt mit qualitativ  
hochwertigen Materialien und  
Komponenten, die recycelt und wieder  
verwendet werden können.  
Dieses Symbol bedeutet, dass  
elektrische und elektronische Geräte  
am Ende ihrer Nutzungsdauer vom  
Hausmüll getrennt entsorgt werden  
sollen.  
Your EverFocus product is designed  
and manufactured with high quality  
materials and components which can  
be recycled and reused.  
This symbol means that electrical and  
electronic equipment, at their end-of-  
life, should be disposed of separately  
from your household waste.  
Please, dispose of this equipment at  
your local community waste  
Bitte entsorgen Sie dieses Gerät bei  
Ihrer örtlichen kommunalen  
Sammelstelle oder im Recycling Centre.  
Helfen Sie uns bitte, die Umwelt zu  
erhalten, in der wir leben!  
collection/recycling centre.  
In the European Union there are  
separate collection systems for used  
electrical and electronic product.  
Please, help us to conserve the  
environment we live in!  
28  
 

Creda Clothes Dryer TVU1 TVR2 User Manual
Edimax Technology Network Card EW 7206GAb User Manual
Electro Voice Portable Speaker B115 M User Manual
FieldServer Computer Drive FS 8700 12 User Manual
Fisher Paykel Double Oven OR30SDPWGX User Manual
Fisher Price Automobile J5246 User Manual
Frigidaire Oven Electric Built in oven User Manual
GE Door 19204 User Manual
GE Oven 840081100 User Manual
GE Thermostat CC SCSTAT User Manual