Behringer Speaker V TONEGM110 User Manual

User’s Manual  
Version 1ꢀ2 July 2004  
 
V-TONE GM110  
V-TONE  
True Analog Modeling 30-Watt Guitar Amp with  
Speaker Simulations and Direct Out  
s
Powerful 30-Watt guitar amplifier, equipped with an original JENSEN® / BUGERATM 10" guitar speaker  
s
Authentic V-TONE Analog Modeling for 3 classic guitar amps, 3 speaker simulation models plus 3 gain  
modes—providing you with 27 modeled sounds  
s
s
Patented* DYNAMIZER circuitry captures every nuance of your playing and lends tube-like compression  
to your tone  
Balanced direct out with XLR connector and ground lift delivers full preamplified sound including all amp,  
speaker, gain mode, drive, EQ and level settings for direct recording or connection of an external power  
amp/cabinet combination  
s
s
s
s
s
s
s
FX loop for external effects devices (rack effects, stomp boxes, wah-wah pedals, etcꢀ)  
Extensive master section with dedicated 3-band EQ and master level control  
Wide-range drive control for super-fat sounds with any pickups  
Headphone output with speaker simulation lets you practice anywhere and at any time  
Additional 4 Ohm speaker out with automatic internal speaker mute  
Rugged construction for years of trouble-free use  
Conceived and designed by BEHRINGER Germany  
* German Patent Noꢀ: 100 15 833  
3
 
V-TONE GM110  
FOREWORD  
1ꢀ INTRODUCTION  
Dear Customer,  
Thank you for purchasing the V-TONE GM110ꢀ The GM110 is  
a modern Guitar Workstation that sets new standards in practice  
amp engineeringꢀ  
welcome to the team of  
BEHRINGER users, and  
thank you very much for  
expressing your confi-  
dence in us by pur-  
chasing the BEHRINGER  
V-TONEꢀ  
When developing the GM110, our primary objective was to  
reproduce the authentic sound of analog guitar amplifiers and at  
the same time provide you with a tool for straightforward  
recordingꢀ The concept of intuitive operation remained a central  
considerationꢀ  
Writing this foreword for  
you gives me great  
pleasure, because it  
represents the cul-  
mination of many months  
of hard work delivered  
by our engineering team  
Many people contributed to this intense development project:  
studio musicians, collectors of vintage guitar amps, music and  
guitar lovers alikeꢀ We even invited guitar amp tuning experts to  
help us develop an amplifier that unites the very best of both  
worldsꢀ  
The demands placed on a guitar amp are nowadays very  
broadꢀ A guitarist should offer a wide array of sounds, but at the  
same time be able to quickly adapt to specific requirements of  
various applications—be it home recording, studio, live perfor-  
mances, etcꢀ That’s why it is very important to us to be able to  
offer you a maximal sound diversity as well as diverse connection  
possibilities with our V-TONEꢀ Fret not: you will quickly master  
the V-TONE and will be able to quickly learn how to use all of its  
capabilities easily and intuitivelyꢀ  
to achieve  
a
very  
ambitious goal: to de-  
velop an outstanding  
guitar amp that is at the  
forefront of what is  
technically possible and that can be used in many different  
applicationsꢀ Our guitar amps offer you strong performance,  
their sound is amazingly clear, and they are easy to use both as  
direct recording amps as well as stage ampsꢀ The task of designing  
our new V-TONEs certainly meant a great deal of responsibility,  
which we assumed by focusing on you, the discerning user and  
musicianꢀ Meeting your expectations also meant a lot of work  
and night shiftsꢀ But it was fun, tooꢀ Developing a product usually  
brings a lot of people together, and what a great feeling it is  
when all who participated in such a project can be proud of  
what they’ve achievedꢀ  
With its up-to-date circuitry, the V-TONE features the  
functionality and dependability of a truly modern guitar ampꢀ Yet  
it is user-friendly and problem-free as if it were a classic tube  
comboꢀ We highly recommend taking your time to truly learn all of  
the V-TONE’s functions so you can reach its maximum potentialꢀ  
1ꢀ1 The design concept  
The philosophy behind BEHRINGER products guarantees a  
no-compromise circuit design and employs the best choice of  
componentsꢀ The operational amplifiers employed by BEHRINGER  
and used in the V-TONE GM110 are exceptional: they boast  
extreme linearity and very low distortion characteristicsꢀ To  
complement this, the choice of components includes low-tolerance  
resistors and capacitors, high-quality potentiometers and  
switches, and several other carefully selected elementsꢀ  
It is our philosophy to share our enjoyment with you, because  
you are the most important member of the BEHRINGER teamꢀ  
With your highly competent suggestions for new products you’ve  
made a significant contribution to shaping our company and making  
it successfulꢀ In return, we guarantee you uncompromising quality  
as well as excellent technical and audio properties at an extremely  
reasonable priceꢀ All of this will enable you to give free rein to  
your creativity without being hampered by budget constraintsꢀ  
The robust housing of your V-TONE, with its oversize power  
supply, gives you the peace of mind that the V-TONE will hold its  
own even under the most demanding stage conditionsꢀ The  
housing is made of high-grade, environment-friendly MDF wood  
consisting of multiply impregnated layersꢀ  
We are often asked how we manage to produce such high-  
quality devices at such unbelievably low pricesꢀ The answer is  
quite simple: it’s you, our customers! Many satisfied customers  
mean large sales volumes enabling us to get better purchasing  
terms for components, etcꢀ Isn’t it only fair to pass this benefit on  
to you? Because we know that your success is our success  
too!  
1ꢀ2 DYNAMIZER technology and  
analog modeling  
I would like to thank all of you who have made the V-TONE  
Series possibleꢀ You have all made your own personal  
contributions, from the developers to the many other employees  
at this company, and to you, the BEHRINGER userꢀ  
When an electric instrument is amplified, that’s where you  
either make it or break itꢀ Unlike the signals that have been mixed  
and mastered, the signals of electric instruments have extremely  
high signal peaks, placing the dynamic range of the amp’s circuitry  
under immense strainꢀ How your amp reacts to these signal  
peaks is one of its most defining characteristicsꢀ  
My friends, it’s been worth the effort!  
Thank you very much,  
That’s why we’ve equipped all V-TONE Series amps with our  
unique DYNAMIZER preamplifier circuitryꢀ It guarantees a lively  
sound with a lot of punch, even when the amp is pushed to its  
limitsꢀ Combine that with our V-TONE analog modeling, and not  
only do you have amazingly authentic tube sounds at your  
fingertips, you also get the dynamic performance typical of the  
respective amp typeꢀ Crystal-clear guitar tones come through  
with transparency, warmth and the compression typical of tube  
ampsꢀ Even as distortion increases, the sound remains lively  
and full of power, without losing any of its assertivenessꢀ  
Uli Behringer  
All along, you have full control over the volumeꢀ Plainly talking,  
you can take the same sound you are used to at your practice  
room and replicate it in your bedroom at much more reasonable  
volume levels, or you can even record yourself while playingꢀ  
4
1ꢀ INTRODUCTION  
 
V-TONE GM110  
+
The following user’s manual will familiarize you with  
the control elements of your new V-TONE and let  
you learn all of its functions! After reading this  
manual, store it somewhere where you can easily  
find in the future, should you need to look up some  
information!  
The fuse mount near the power cord connector has three  
triangular markingsꢀ Two of these triangles are facing opposite  
one anotherꢀ Your V-TONE is set up for the voltage indicated  
near these markings, and can be altered by turning the fuse  
mount by 180 degreesꢀ ATTENTION: This does not apply to  
export models built for 120 V, for example!  
+
If you use your V-TONE unit with a different voltage,  
you must change the fuses accordingly! The correct  
value of the fuses needed can be found in the  
chapter “SPECIFICATIONS”!  
1ꢀ3 Before you get started  
1ꢀ3ꢀ1 Shipment  
The V-TONE was carefully packed at the assembly plant to  
assure secure transportꢀ  
+
Faulty fuses must be replaced with fuses of  
appropriate rating, without exception! The correct  
value of the fuses needed can be found in the  
chapter “SPECIFICATIONS”!  
Should the condition of the cardboard box suggest that your  
V-TONE may have been damaged in transport, please inspect  
the unit immediately and look for physical indications of damageꢀ  
Power is delivered via the cable that was delivered with the V-  
TONEꢀ All mandatory safety precautions have been adhered toꢀ  
+
Damaged equipment should NEVER be sent directly  
to us! Please inform the dealer from whom you  
acquired it immediately as well as the  
transportation company from which you took  
delivery! Otherwise, all claims for replacement/  
repair may be rendered invalid!  
+
Please make sure that all your equipment is  
grounded at all times! For your own protection, you  
should never tamper with the grounding of the cable  
or the unit itself! The unit shall always be connected  
to a mains socket outlet with a protective earthing  
connection! You can eliminate humming problems  
caused by grounding at the D!I! OUT by pressing the  
1ꢀ3ꢀ2 Initial operation  
GND switch (Groundlift,  
)!  
Please make sure that your V-TONE is provided with sufficient  
ventilation, and never place it on other amplifiers or in the vicinity  
of a heater to avoid the risk of overheatingꢀ  
1ꢀ3ꢀ3 Warranty  
Please send the completely filled out warranty card within 14  
days of purchase to us, as warranty claims may otherwise be  
rendered invalidꢀ The serial number of your V-TONE is located  
on the rearꢀ Alternatively, you may register online at  
wwwꢀbehringerꢀcomꢀ  
+
Before plugging your V-TONE into a power socket,  
please make sure you have selected the correct  
voltage:  
2ꢀ CONTROL ELEMENTS  
2ꢀ1 Front panel  
Figꢀ 2ꢀ1: Front panel control elements  
INPUT is the GM110’s 1/4" jack input for your guitarꢀ Use a  
commercial 1/4" jack mono cable (not from a DIY shop, but  
from a specialist music dealer)ꢀ  
differentiated, the CALIF(ORNIAN) setting is particularly  
suitable for singing lead soundsꢀ  
With the MODE switch, you choose between one of three  
possible gain settings (CLEAN, HI GAIN and HOT) to achieve  
the basic sound selected with the AMP switchꢀ  
The DRIVE control determines the amplification in the input  
sectionꢀ It allows you to finely tune the GM110 preset to the  
output level of your guitar pick-up (depending on selected  
amp, mode and speaker combination) in order to achieve  
the desired degree of distortionꢀ  
The SPEAKER switch provides you with simulations of  
two classic guitar loudspeakers: 4x12"-loudspeakers in a  
closed back enclosure (UꢀKꢀ), and 2x12" loudspeakers,  
open back (UꢀSꢀ)ꢀ In addition, we have also installed a  
further frequency response correction (FLAT) that is  
specially adapted to the GM110 enclosureꢀ  
+
Use the DRIVE control to set the desired sound and  
use the MASTER control to set the desired volume!  
The AMP switch enables you to emulate the basic sounds  
from three guitar amp designs; these are based on classic  
amp models and will be familiar to you from numerous  
recordingsꢀ The TWEED setting delivers transparent  
sounds, clear as a bell, with dynamic bass responseꢀ The  
BRITISH setting has an aggression that comes straight from  
the heart and is powerful with an unmistakable ability to  
make itself heardꢀ Fuller and more balanced, and yet subtly  
The LOW control in the EQ section enables you to boost or  
cut the bass frequenciesꢀ  
With the MID control, you can boost/cut the midrange  
frequenciesꢀ  
The HIGH control governs the upper frequency rangeꢀ  
5
2ꢀ CONTROL ELEMENTS  
 
V-TONE GM110  
With the MASTER control, you determine the overall and  
headphone volume of your V-TONE GM110ꢀ It should be  
set fully to the left when you operate the POWER switch or  
disconnect the instrument cable from the guitar or ampꢀ  
The POWER switch should always be in the “Off” position  
when you are about to connect your unit to the mainsꢀ  
+
Attention: The POWER switch does not fully  
disconnect the unit from the mains! Unplug the  
power cord completely when the unit is not used  
for prolonged periods of time!  
Use the POWER switch to put the GM110 into operationꢀ  
2ꢀ2 Rear panel  
BEHRINGER® V–TONE  
MODEL GM110  
CONCEIVED AND DESIGNED  
BY BEHRINGER GERMANY.  
ASSEMBLED IN CHINA UNDER  
ISO9000 CERTIFIED  
MANAGEMENT SYSTEM.  
CAUTION  
REPLACE WITH SAME FUSE  
TYPE AND RATING.  
ATTENTION  
UTILISER UN FUSIBLE DE  
RECHANGE DE MEME  
TYPE ET CALIBRE.  
OUTPUT  
230  
V
:
50/60 Hz 70  
W
FUSE:  
˜
T
1.0 250  
A
H
V
Figꢀ 2ꢀ2: Rear panel connectors  
FUSEHOLDER / VOLTAGE SELECTIONꢀ Before you  
connect the device to the network, please make sure that  
your local voltage matches the voltage indicated on the  
unitꢀ Blown fuses may only be replaced by fuses of the  
same type and ratingꢀ Some models allow for inserting the  
fuse holder in two different positions in order to switch  
over from 230 V to 120 V operation, and vice versaꢀ Please  
note that, for 120 V operation outside Europe, you need to  
use a fuse of a higher ratingꢀ The network connection is  
made via a STANDARD IEC INLET SOCKETꢀ Use the  
enclosed power cord to connect the unit to the mainsꢀ  
At the DꢀIꢀ OUT output (balanced XLR socket), you can tap  
the audio signal of the V-TONE GM110 in order, for example,  
to feed it into a mixing console and record itꢀ This audio  
signal is frequency-corrected (Speaker Simulation)ꢀ The  
level of the DꢀIꢀ OUT (maxꢀ +22 dBu) is designed to provide  
simple connection to mixers or other audio devicesꢀ  
With the GND LIFT switch, you can unplug the electrical  
bonding of the DꢀIꢀ OUT, if ground loop or humming problems  
occurꢀ  
FX SEND is the output socket for the serial effects path of  
the GM110ꢀ You can use this to loop in the external effects  
(eꢀgꢀ a wah-wah pedal) or to connect an external power  
amplifier, should you require a greater outputꢀ The internal  
signal path will not be interruptedꢀ The frequency-corrected  
signal at the FX SEND socket is affected by all GM110  
controlsꢀ  
SERIAL NUMBERꢀ Please take the time to fill out the  
warranty card within 14 days of purchasing the device,  
otherwise you will lose your extended warrantyꢀ Or simply  
register online at wwwꢀbehringerꢀcomꢀ  
You can use the SPEAKER socket to connect an additional  
loudspeaker to your V-TONE GM110ꢀ The external  
loudspeaker should have an impedance of 4 Ohmsꢀ When  
using this socket, the internal loudspeaker is mutedꢀ For  
additional information on connecting an external  
loudspeaker, refer to chapter 4ꢀ1ꢀ  
The output of the looped-in effects device is connected to  
the FX RETURN socketꢀ When you connect a cable to this  
socket, you interrupt the internal signal pathꢀ  
+
Please note that, when using the serial effects path,  
the effects device will control the level of wet  
(affected) signal to dry (direct) signal!  
The 6ꢀ3 mm PHONES jack allows you to monitor the GM110’s  
audio signal with a pair of commercially available  
headphonesꢀ As soon as this socket is used, the  
loudspeaker will be mutedꢀ  
+
+
Since speakers can have quite an impact on the  
sound of a guitar amp, both the headphones and  
D!I! OUT signals are frequency-corrected (with  
speaker correction)! Without this frequency  
correction extreme treble frequencies would  
deteriorate the sound!  
Low-impedance headphones may begin to produce  
distortion at certain volume levels! In such cases,  
please reduce the volume by turning back the  
MASTER control!  
6
2ꢀ CONTROL ELEMENTS  
 
V-TONE GM110  
3ꢀ WIRING TIPS  
3ꢀ1 Standard set-up consisting of guitar, external effects device and simultaneous recording  
Figꢀ 3ꢀ1: Standard set-up for recording with the V-TONE GM110  
To use your V-TONE GM110 for rehearsals, in the studio or on  
stage, please wire up the unit as shown in figꢀ 2ꢀ1ꢀ Of course,  
you can also use a wah-wah or other pedal effect instead of the  
external 19" effects unitꢀ Connecting the headphones will mute  
the built-in speakerꢀ  
If you wish to use a guitar tuner, please connect it to the FX  
SEND of your V-TONE GM110ꢀ If there is no further effects  
device connected, you can leave the FX RETURN as it isꢀ When  
using an external effects device, the tuner should be placed  
before the effects device to prevent the tuner from receiving  
any effects signalꢀ  
4ꢀ AUDIO CONNECTIONS  
Figꢀ 4ꢀ1: 1/4" TS connector (input, FX send, FX return,  
speaker)  
The BEHRINGER V-TONE GM110 is fitted with audio inputs and  
outputs in the form of 1/4" mono jacksꢀ The exceptions to this are  
the headphones output and the DꢀIꢀ OUTꢀ  
+
+
Please ensure that only qualified personnel install  
and operate the device!  
Please make sure that all units have a proper  
ground connection! For your own safety, never  
remove or disable the ground conductor of the unit  
or of the AC power cable! Instead, you can eliminate  
hum problems caused by grounding (e!g! when  
connected to a mixing console) by pressing the  
GND switch (Groundlift,  
)!  
4ꢀ2: Wiring of a stereo headphones plug  
7
4ꢀ AUDIO CONNECTIONS  
 
V-TONE GM110  
5ꢀ SPECIFICATIONS  
AUDIO INPUTS  
Guitar input  
Connector  
1/4" mono jack socket  
Type  
RF filtered input  
Input impedance  
FX return  
Connector  
Input impedance  
approxꢀ 1 Munbalanced  
1/4" mono jack socket  
approxꢀ 1 Munbalanced  
AUDIO OUTPUTS  
FX send  
Connector  
1/4" mono jack socket  
Type  
Output impedance  
Low-impedance line level output  
approxꢀ 100 unbalanced  
Figꢀ 4ꢀ3: XLR connectors (DꢀIꢀ Out)  
DꢀIꢀ Out  
Connector  
Type  
XLR  
Balanced, low-impedance line  
level output  
4ꢀ1 Loudspeaker connection  
Output impedance  
Maxꢀ output level  
approxꢀ 100 Ω  
The GM110 features a loudspeaker connection (mono jack  
socket) that allows you to hook up a supplementary speakerꢀ  
Optimum adaptation of the amp to the loudspeaker is ensured  
with an 4 loudspeakerꢀ With too high an impedance load, the  
maximum power output will drop in proportion to the resistance  
connectedꢀ  
+22 dBu  
LOUDSPEAKER OUPUT  
Connector  
Load impedance (nomꢀ)  
1/4" mono jack socket  
4 Ω  
SYSTEM SPECIFICATIONS  
Power amp output  
+
Do not use an instrument cable to connect an  
external loudspeaker, rather use special  
loudspeaker cable! This will prevent any  
unnecessary losses of sound and output!  
30 Watts RMS into 4 Ω  
a
LOUDSPEAKER  
Type  
10" Vintage loudspeaker, model  
JENSEN®  
JCH10/35  
or  
BUGERATM loudspeaker  
4 Ω  
Impedance  
Power handling  
35 Watts (JENSEN®)  
60 Watts (BUGERATM  
)
POWER SUPPLY  
Mains voltage  
USA/Canada  
120 V~, 60 Hz  
Europe/UꢀKꢀ/Australia 230 V~, 50 Hz  
Japan  
100 V~, 50 - 60 Hz  
General export model 120 /230 V~, 50 - 60 Hz  
Power consumption 70 W maximum  
Fuse  
100 - 120 V~: T 2 A H 250 V  
200 - 240 V~: T 1 A H 250 V  
Standard IEC receptacle  
Mains connection  
DIMENSIONS/WEIGHT  
Dimensions (H x W x D)  
approxꢀ 15" (381 mm) x 14 ½"  
(369 mm) x 9 ½" (242 mm)  
approxꢀ 12ꢀ5 kg  
Weight  
BEHRINGER is constantly striving to maintain the highest quality standardsꢀ Modifications  
may be made to existing products without prior noticeꢀ Specifications and appearance may differ  
from those listed or illustratedꢀ  
8
5ꢀ SPECIFICATIONS  
 
V-TONE GM110  
6ꢀ WARRANTY  
§ 1 WARRANTY CARD/ONLINE REGISTRATION  
3ꢀ Free inspections and maintenance/repair work are expressly  
excluded from this warranty, in particular, if caused by improper  
handling of the product by the userꢀ This also applies to defects  
caused by normal wear and tear, in particular, of faders,  
crossfaders, potentiometers, keys/buttons, tubes, guitar strings,  
illuminants and similar partsꢀ  
To be protected by the extended warranty, the buyer must  
complete and return the enclosed warranty card within 14 days  
of the date of purchase to BEHRINGER Spezielle Studiotechnik  
GmbH, in accordance with the conditions stipulated in § 3ꢀ Failure  
to return the card in due time (date as per postmark) will void any  
extended warranty claimsꢀ Based on the conditions herein, the  
buyer may also choose to use the online registration option via  
the Internet (wwwꢀbehringerꢀcom or wwwꢀbehringerꢀde)ꢀ  
4ꢀ Damages/defects caused by the following conditions are  
not covered by this warranty:  
s improper handling, neglect or failure to operate the unit in  
compliance with the instructions given in BEHRINGER user  
or service manualsꢀ  
§ 2 WARRANTY  
1ꢀ BEHRINGER (BEHRINGER Spezielle Studiotechnik GmbH  
including all BEHRINGER subsidiaries listed on the enclosed page,  
except BEHRINGER Japan) warrants the mechanical and  
electronic components of this product to be free of defects in  
material and workmanship for a period of one (1) year* from the  
original date of purchase, in accordance with the warranty  
regulations described belowꢀ If the product shows any defects  
within the specified warranty period that are not excluded from  
this warranty as described under § 4, BEHRINGER shall, at its  
discretion, either replace or repair the product using suitable  
new or reconditioned partsꢀ In the case that other parts are used  
which constitute an improvement, BEHRINGER may, at its  
discretion, charge the customer for the additional cost of these  
partsꢀ  
s connection or operation of the unit in any way that does not  
comply with the technical or safety regulations applicable in  
the country where the product is usedꢀ  
s damages/defects caused by force majeure or any other  
condition that is beyond the control of BEHRINGERꢀ  
5ꢀ Any repair or opening of the unit carried out by unauthorized  
personnel (user included) will void the warrantyꢀ  
6ꢀ If an inspection of the product by BEHRINGER shows that  
the defect in question is not covered by the warranty, the  
inspection costs are payable by the customerꢀ  
7ꢀ Products which do not meet the terms of this warranty will  
be repaired exclusively at the buyer’s expenseꢀ BEHRINGER will  
inform the buyer of any such circumstanceꢀ If the buyer fails to  
submit a written repair order within 6 weeks after notification,  
BEHRINGER will return the unit CꢀOꢀDꢀ with a separate invoice  
for freight and packingꢀ Such costs will also be invoiced  
separately when the buyer has sent in a written repair orderꢀ  
2ꢀ If the warranty claim proves to be justified, the product will  
be returned to the user freight prepaidꢀ  
3ꢀ Warranty claims other than those indicated above are  
expressly excludedꢀ  
§ 3 RETURN AUTHORIZATION NUMBER  
1ꢀ To obtain warranty service, the buyer (or his authorized  
dealer) must call BEHRINGER (see enclosed list) during normal  
business hours BEFORE returning the productꢀ All inquiries must  
be accompanied by a description of the problemꢀ BEHRINGER  
will then issue a return authorization numberꢀ  
§ 5 WARRANTY TRANSFERABILITY  
This warranty is extended exclusively to the original buyer  
(customer of retail dealer) and is not transferable to anyone  
who may subsequently purchase this productꢀ No other person  
(retail dealer, etcꢀ) shall be entitled to give any warranty promise  
on behalf of BEHRINGERꢀ  
2ꢀ Subsequently, the product must be returned in its original  
shipping carton, together with the return authorization number to  
the address indicated by BEHRINGERꢀ  
§ 6 CLAIM FOR DAMAGES  
Failure of BEHRINGER to provide proper warranty service shall  
not entitle the buyer to claim (consequential) damagesꢀ In no  
event shall the liability of BEHRINGER exceed the invoiced value  
of the productꢀ  
3ꢀ Shipments without freight prepaid will not be acceptedꢀ  
§ 4 WARRANTY REGULATIONS  
1ꢀ Warranty services will be furnished only if the product is  
accompanied by a copy of the original retail dealer’s invoiceꢀ  
Any product deemed eligible for repair or replacement under the  
terms of this warranty will be repaired or replacedꢀ  
§ 7 OTHER WARRANTY RIGHTS AND NATIONAL LAW  
1ꢀ This warranty does not exclude or limit the buyer’s statutory  
rights provided by national law, in particular, any such rights  
against the seller that arise from a legally effective purchase  
contractꢀ  
2ꢀ If the product needs to be modified or adapted in order to  
comply with applicable technical or safety standards on a national  
or local level, in any country which is not the country for which  
the product was originally developed and manufactured, this  
modification/adaptation shall not be considered a defect in  
materials or workmanshipꢀ The warranty does not cover any  
such modification/adaptation, irrespective of whether it was  
carried out properly or notꢀ Under the terms of this warranty,  
BEHRINGER shall not be held responsible for any cost resulting  
from such a modification/adaptationꢀ  
2ꢀ The warranty regulations mentioned herein are applicable  
unless they constitute an infringement of national warranty lawꢀ  
* Customers in the European Union please contact BEHRINGER  
Germany Support for further detailsꢀ  
Technical specifications and appearance subject to change without noticeꢀ The information contained herein is correct at the time of printingꢀ  
JENSEN® and its respective logo are registered trademarks of its respective ownerꢀ Their use neither constitutes a claim of the trademarks by  
BEHRINGER® nor affiliation of the trademark owners with BEHRINGER®ꢀ BEHRINGER® accepts no liability for any loss which may be suffered by  
any person who relies either wholly or in part upon any description, photograph or statement contained hereinꢀ Colours and specification may vary  
slightly from productꢀ Products are sold through our authorised dealers onlyꢀ Distributors and dealers are not agents of BEHRINGER® and have  
absolutely no authority to bind BEHRINGER® by any express or implied undertaking or representationꢀ No part of this manual may be reproduced  
or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for any purpose, without  
the express written permission of BEHRINGER Spezielle Studiotechnik GmbHꢀ BEHRINGER® is a registered trademarkꢀ  
ALL RIGHTS RESERVEDꢀ© 2004 BEHRINGER Spezielle Studiotechnik GmbHꢀ BEHRINGER Spezielle Studiotechnik GmbH, Hanns-Martin-  
Schleyer-Strꢀ 36-38, 47877 Willich-Münchheide II, Germanyꢀ Telꢀ +49 2154 9206 0, Fax +49 2154 9206 4903  
6ꢀ WARRANTY  
9
 

Acer Projector PD311 User Manual
Activision Video Games 47875841147 User Manual
Addtron Technology Network Router TELEWELL TW 640 User Manual
Aluratek Network Card ACDUES350F2TB User Manual
Amana Range AER5845RAW User Manual
American DJ DJ Equipment XP3 User Manual
American Dryer Corp Clothes Dryer AD 78 IV User Manual
Audiovox Stereo System ACD16 User Manual
Behringer Speaker System B112D User Manual
Beko Dishwasher D 5001 E User Manual