Icom IC 7200 User Manual

USB DRIVER  
INSTALLATION GUIDE  
Thank you for using the Icom Download Service.  
Please read this installation guide before installing the USB driver into your PC that is connected to the IC-7200  
with the USB (Universal Serial Bus) cable (third party).  
OVERVIEW  
When the transceiver is connected to a PC with the  
USB cable, the following operations can be performed;  
System requirements  
The PC which supports the following OS (Operating  
System) is required;  
• Remote control operation (CI-V: Icom Communica-  
tion Interface-V) by the PC.  
• Modulation input from the PC.  
Microsoft® Windows Vista™  
Microsoft® Windows® XP  
Microsoft® Windows® 2000  
• Received audio output to the PC.  
NOTE:  
USB cable  
(third party)  
• The USB driver is not supported for Microsoft®  
Windows® XP (64 bit).  
• Icom is not responsible for whole performance of  
the PC that supports above OS.  
• In this installation guide, the above OS are de-  
scribed as “Windows Vista,” “Windows XP” and  
“Windows 2000.”  
Transceiver  
PC  
NOTE:  
PC software (third party) may be required. (p. 18)  
• The CT-17 ci-v level converter is required for re-  
mote control operation (CI-V) when the USB cable  
is not used. See p. 88 in the IC-7200 instruction  
manual for details.  
Item requirements  
• USB cable (A-B type/third party)  
• The transceiver connection may not be recog-  
nized by the PC because of the USB cable length.  
Using the shorter USB cable as possible is rec-  
ommended.  
A type  
B type  
• PC (with USB 1.1 or 2.0)  
• Installed audio player  
• PC software (third party)  
- See p. 18 for details.  
Icom, Icom Inc. and the  
logo are registered trademarks of Icom  
Incorporated (Japan) in the United States, the United Kingdom, Germany,  
France, Spain, Russia and/or other countries.  
Microsoft, Windows and Windows Vista are either registered trademarks  
or trademarks of Microsoft Corporation in the United States and/or other  
countries.  
All other products or brands are registered trademarks or trademarks of their  
respective holders.  
1
PREPARING  
Before installing the USB driver  
Icom HP gives the USB driver download service.  
Before installing the USB driver, download the follow-  
ing compressed file.  
• USB driver  
(File name: 7200UsbDrv_v100.zip)  
Icom is not responsible for any damage or lack of  
data resulting from the use of the USB driver.  
3
DRIVER INSTALLATION  
Windows Vista  
NOTE:  
NEVER connect the transceiver to the PC with the USB cable (third party) until the USB driver installation  
has been completed.  
• The USB driver for Windows Vista does not support the automatic recognition system.  
The displayed dialogue boxes, indications or oper-  
ations may differ slightly from the following instruc-  
tions according to your system conditions or envi-  
ronment.  
t“A program needs your permission to continue” dia-  
logue box appears as below.  
Click [Continue].  
q
Make sure that the transceiver is not connected to  
the PC.  
Click  
w Start up Windows.  
• Quit all other application if running.  
e Double-click the “WinVista” folder.  
• The folder construction: “7200UsbDrv_v100”  
“Driver” “WinVista”  
yVerify the installation location, then click [Install].  
Click  
Double click  
uWindows starts scanning for the system, then starts  
installing the USB driver.  
r Double-click the “CP210xVCPInstaller.exe” to start  
up the USB driver installer.  
iAfter the installation is completed, click [OK].  
• Restarting the PC is recommended.  
Click  
Double click  
Continues to the next page  
4
DRIVER INSTALLATION  
Windows Vista (Continued)  
oAfter restarting the PC, connect the transceiver to  
the PC with the USB cable (third party) as shown  
below.  
!Turn the transceiver power ON.  
• “Installing device driver software” appears as below.  
• Be sure to connect the USB cable correctly and not up-  
side down.  
REMOTE  
!After the dialogue appears as below, USB driver  
installation has been completed.  
KEY  
SEND  
ALC  
ACC  
Transceiver  
To USB jack  
Type B  
USB cable  
(third party)  
Type A  
PC  
To USB port  
5
DRIVER INSTALLATION (Continued)  
Windows XP  
NOTE:  
BE SURE to connect the transceiver to the PC with the USB cable (third party) before installing the USB  
driver.  
The displayed dialogue boxes, indications or oper-  
ations may differ slightly from the following instruc-  
tions according to your system conditions or envi-  
ronment.  
tThe “Welcome to the Found New Hardware Wizard”  
will come up as below.  
Select “No, not this time,then click [Next>].  
q
Make sure that the transceiver is not connected to  
the PC.  
w Start up Windows.  
• Quit all other application if running.  
eConnect the transceiver to the PC with the USB  
cable (third party) as shown below.  
• Be sure to connect the USB cable correctly and not up-  
side down.  
Select  
Click  
REMOTE  
ySelect “Install from a list or specific location  
(Advanced),then click [Next>].  
KEY  
SEND  
ALC  
ACC  
Transceiver  
To USB jack  
Type B  
Select  
USB cable  
(third party)  
Click  
uSelect “Search for the best driver in these locations.”  
then select “Include this location in the search,and  
click [Browse].  
Type A  
PC  
Select  
To USB port  
Click  
Select  
rTurn the transceiver power ON.  
• “Found New Hardware” appears as below.  
Continues to the next page  
6
DRIVER INSTALLATION  
Windows XP (Continued)  
i Select the “Win” folder, then click [OK].  
• The folder construction: “7200UsbDrv_v100” ➞  
“Driver” “Win”  
!Windows starts installing the USB driver.  
Select  
Click  
oClick [Next>].  
!After the installation is completed, click [Finish].  
Click  
Click  
!The Wizard starts searching for the driver and  
!
After clicking [Finish], the dialogue appears as below.  
shows the dialogue below during search.  
!The “Welcom to the Found New Hardware Wizard”  
will come up again to install the USB serial port  
driver.  
Select “No, not this time,then click [Next>].  
!After the driver is found, the “Hardware Installation”  
dialogue box appears as below.  
Click [Continue Anyway] to start the installation.  
Select  
Click  
Click  
Continues to the next page  
7
DRIVER INSTALLATION  
Windows XP (Continued)  
!Select “Install from a list or specific location  
@The Wizard starts searching for the driver and  
(Advanced),then click [Next>].  
shows the dialogue below during search.  
Select  
Click  
@After the driver is found, the “Hardware Installation”  
dialogue box appears as below.  
!Select “Search for the best driver in these locations.”  
then select “Include this location in the search:”,  
and click [Browse].  
Click [Continue Anyway] to start the installation.  
Select  
Click  
Select  
Click  
@Windows starts installing the USB driver.  
! Select the “Win” folder, then click [OK].  
• The folder construction: “7200UsbDrv_v100” ➞  
“Driver” “Win”  
Select  
Click  
@After the installation is completed, click [Finish].  
!Click [Next>].  
Click  
Click  
@
After clicking [Finish], the dialogue appears as below.  
• Restarting the PC is recommended.  
8
DRIVER INSTALLATION (Continued)  
Windows 2000  
NOTE:  
BE SURE to connect the transceiver to the PC with the USB cable (third party) before installing the USB  
driver.  
The displayed dialogue boxes, indications or oper-  
ations may differ slightly from the following instruc-  
tions according to your system conditions or envi-  
ronment.  
tThe “Found New Hardware Wizard” will come up as  
below.  
Click [Next>].  
q
Make sure that the transceiver is not connected to  
the PC.  
w Start up Windows.  
• Quit all other application if running.  
eConnect the transceiver to the PC with the USB  
cable (third party) as shown below.  
• Be sure to connect the USB cable correctly and not up-  
side down.  
Click  
REMOTE  
ySelect “Search for a suitable driver for my device  
(recommended),then click [Next>].  
KEY  
SEND  
ALC  
ACC  
Transceiver  
To USB jack  
Type B  
Select  
USB cable  
(third party)  
Click  
uSelect “Specify a location,then click [Next>].  
Type A  
PC  
To USB port  
Select  
Click  
rTurn the the transceiver power ON.  
• “Found New Hardware” appears as below.  
iClick [Browse...].  
Click  
Continues to the next page  
9
DRIVER INSTALLATION  
Windows 2000 (Continued)  
oSelect “slabbus.inf” in the “Win” folder, then click  
!After the installation is completed, click [Finish].  
[Open].  
• The folder construction: “7200UsbDrv_v100” ➞  
“Driver” “Win”  
Select  
“slabbus.inf”  
Click  
Click  
!The “Found New Hardware Wizard” appears again.  
Click [Next>].  
!Click [OK].  
Click  
Click  
!When the driver is found, the following dialogue is  
displayed.  
Click [Next>] to start the installation.  
!Select “Search for a suitable driver for my device  
(recommended),then click [Next>].  
Click  
Select  
Click  
!Select “Specify a location,then click [Next>].  
Select  
Click  
Continues to the next page  
10  
DRIVER INSTALLATION  
Windows 2000 (Continued)  
!Click [Browse...].  
!When the driver is found, the following dialogue is  
displayed.  
Click [Next>] to start the installation.  
Click  
!Select “slabw2k.inf” in the “Win” folder, then click  
[Open].  
• The folder construction: “7200UsbDrv_v100” ➞  
“Driver” “Win”  
Click  
@After the installation is completed, click [Finish].  
Select  
“slabw2k.inf”  
• Restarting the PC is recommended.  
Click  
!Click [OK].  
Click  
Click  
11  
COM PORT CONFIRMATION  
After the driver installation is completed, confirming the driver availability and the port number is recommended.  
Windows Vista  
Windows XP  
q Start up Windows.  
For Windows 2000:  
w Right click “Computer,then select “Properties.”  
• “Computer” is available in <Start> menu.  
e “System” screen appears as below.  
Click [Device Manager].  
Refer to the following instructions because the  
operations of Windows 2000 are similar to Windows  
XP.  
q Start up Windows.  
w Right click “My Computer,then select “Properties.”  
• “My Computer” is available in <Start> menu.  
e “System Properties” screen appears as below.  
Click [Hardware] tab and then click [Device Man-  
ager].  
Click  
Click  
Click  
r In case “User Account Control” dialogue box ap-  
pears as below, click [Continue].  
r “Device Manager” screen appears.  
Click “ ” of “Ports (COM&LPT).”  
t Confirm “CP210x USB to UART Bridge Controller  
(COMM)” is displayed.  
• If “!” or “×” indicator is displayed on the “Device Man-  
ager” screen, the driver may not be installed properly.  
Un-install the USB driver then reinstall in such cases.  
Click  
M” is the COM port number, that is used for the  
communication setting with the utility software.  
t “Device Manager” screen appears.  
Click “ ” of “Ports (COM&LPT).”  
y Confirm “CP210x USB to UART Bridge Controller  
(COMM)” is displayed.  
q Click “  
• If “!” or “×” indicator is displayed on the “Device Man-  
ager” screen, the driver may not be installed properly.  
Un-install the USB driver then reinstall in such cases.  
M” is the COM port number, that is used for the  
communication setting with the utility software.  
q Click “  
Check the COM port number.  
(In this example, the USB serial  
COM port number is “8.)  
w
Check the COM port number.  
(In this example, the USB serial  
COM port number is “8.)  
w
12  
DRIVER UNINSTALLATION  
The displayed dialogue boxes or indications may differ slightly from the following instructions according to your  
system conditions, or environment.  
Windows Vista  
Windows XP  
q Start up Windows.  
For Windows 2000:  
w Select the “Control Panel” in the Start menu.  
• The control panel appears as shown in the next step  
below.  
e Click the “Uninstall a program.”  
• The “Uninstall or Change a Program” menu appears.  
Refer to the following instructions because the  
operations of Windows 2000 are similar to Windows  
XP.  
q Start up Windows.  
w Select the “Control Panel” in the Start menu.  
• The control panel appears as shown in the next step  
below.  
e Click the “Add or Remove Programs.”  
• The “Add or Remove Programs” menu appears.  
Click  
Click  
r Double-click “Silicon Laboratories CP210x USB to  
UART Bridge (DriverRemoval).”  
r Select “CP210x USB to UART Bridge Controller,”  
t In case “User Account Control” dialogue box ap-  
then click [Change/Remove].  
pears as below, click [Continue].  
Click  
Click  
y The “Confirm Uninstall” appears.  
Click [Uninstall] to uninstall the program from the  
PC.  
t The “Ready to uninstall CP210x USB to UART  
Bridge Controller Driver?” appears.  
Click [Yes] to uninstall the program from the PC.  
• The uninstallation starts.  
• The uninstallation starts.  
Click  
Click  
y After the uninstall is completed, click [OK.]  
u After the uninstall is completed, click [OK].  
• Restarting the PC is recommended.  
• Restarting the PC is recommended.  
Click  
Click  
13  
FORYOUR REFERENCE  
When the transceiver is connected to a PC with the USB cable (third party), remote control operation can be per-  
formed with the CI-V command.  
The IC-7200 has the USB-Serial convert function, so the PC recognizes the connected transceiver as COM port  
and the CI-V control software can be used.  
Simultaneous use of the [USB] and [REMOTE] jacks are available.  
COM Port setting  
To change the COM Port number setting, connect the transceiver to the PC and then turn the transceiver power ON  
after the driver installation is completed.  
Windows Vista  
q Start up Windows.  
y Click [Port Settings] tab, then click [Advanced...].  
w Right click “Computer,then select “Properties.”  
• “Computer” is available in <Start> menu.  
e “System” screen appears as below.  
Click [Device Manager].  
Click  
Click  
Click  
r In case “User Account Control” dialogue box ap-  
pears as below, click [Continue].  
u Set the desired COM port number, then click [OK].  
Click  
Click  
Set  
t “Device Manager” screen appears.  
Right click “CP210x USB to UART Bridge Controller  
(COMM)” and then click “Properties.”  
i Click [OK] to close the screen.  
M” is the COM port number, that is used for the  
communication setting with the utility software.  
Right-click  
Click  
Click  
14  
FOR YOUR REFERENCE  
COM Port setting (Continued)  
Windows XP  
t Click [Port Settings] tab, then click [Advanced...].  
For Windows 2000:  
Refer to the following instructions because the  
operations of Windows 2000 are similar to Windows  
XP.  
Click  
q Start up Windows.  
w Right click “My Computer,then select “Properties.”  
• “My Computer” is available in <Start> menu.  
e “System Properties” screen appears as below.  
Click [Hardware] tab and then click [Device Man-  
ager].  
Click  
Click  
Click  
y Set the COM port number if desired, then click  
[OK].  
r “Device Manager” screen appears.  
Right click “CP210x USB to UART Bridge Controller  
(COMM)” and then click “Properties.”  
Click  
M” is the COM port number, that is used for the  
communication setting with the utility software.  
Set  
u Click [OK] to close the screen.  
Right-click  
Click  
Click  
15  
FOR YOUR REFERENCE (Continued)  
About audio  
When the transceiver is connected to a PC with the USB cable (third party), the following operations can be  
performed;  
• Received audio output to the PC.  
• Modulation input from the PC.  
The set mode item ‘Modulation input (Data OFF)’ or ‘Modulation input (Data ON)’ must be set as “U” (USB) for  
modulation input from the PC.  
See p. 17 on this installation guide or p. 77 on the IC-7200 instruction manual for details of settings.  
[Received audio output to the PC]  
The received audio output format  
The received audio output format from the USB jack is listed as below.  
The number of data bit 16-bit  
The received audio output Sampling rate*  
8/11.025/16/22.05/32/44.1/48 kHz  
The number of channel Monaural (Stereo: The same audio signals are output from both L/R.)  
* The sampling rate other than those above can be used according to the application.  
The received audio output  
The same audio signals are output from the USB jack and the ACC socket.  
• The received audio is always output regardless of the squelch condition (open/close).  
(The beep tones and the voice synthesizer announcements are not output).  
• The received audio output level cannot be adjusted with the [AF] control.  
Operating mode  
The modulation input can be used when SSB (LSB/USB), SSB data (LSBD/USBD), AM and AM data (AMD)  
mode is in use.  
16  
FOR YOUR REFERENCE  
About audio (Continued)  
The modulation input settings  
To input the audio signal from the USB jack of the transceiver, set the modulation input connector as “USB” in the  
set mode item ‘Modulation input (Data OFF)’ or ‘Modulation input (Data ON)’, or CI-V system (command).  
• When the data mode is OFF (SSB or AM mode is in use)  
<Set mode>  
M-CH/RIT  
SET  
q Push and hold  
for 1 sec. twice to enter  
the set mode.  
w Rotate [M-CH] to select “Mod.”  
e Rotate [DIAL] to select the modulation input  
connector as “U” (USB) when the data mode is  
OFF.  
ANF  
METER  
NB NR  
1
1.8  
2
3.5  
3
7
V/M  
A/B  
=
SPLIT  
4
10  
5
14  
6
18  
MW  
M-CL  
AGC  
VOX  
COMP 7  
21  
8
24  
9
28  
SCAN  
.
0
50  
F-INP ENT  
BAND  
MODE  
TS  
RIT GENE MNF  
P
.AMP  
TUNER FILTER  
SPCH  
ATT  
M-CH/RIT  
SET  
[DIAL]  
[M-CH]  
U (USB)  
M-CH/RIT  
SET  
r Push  
to exit the set mode and return to  
normal operation.  
<CI-V system>  
Send the command “FE FE 76 E0 1A 03 23 03 FD”* to the transceiver.  
USB  
*The transceiver’s address is described as “76” and the controller’s address is described as “E0” for examples  
in this guide.  
• When the data mode is ON (SSB data or AM data mode is in use)  
<Set mode>  
M-CH/RIT  
SET  
q Push and hold  
for 1 sec. twice to enter  
the set mode.  
w Rotate [M-CH] to select “D-Mod.”  
e Rotate [DIAL] to select the modulation input con-  
nector as “U” (USB) when the data mode is ON.  
ANF  
METER  
NB NR  
1
1.8  
2
3.5  
3
7
V/M  
A/B  
=
SPLIT  
4
10  
5
14  
6
18  
MW  
M-CL  
AGC  
VOX  
COMP 7  
21  
8
24  
9
28  
SCAN  
.
0
50  
F-INP ENT  
BAND  
MODE  
TS  
RIT GENE MNF  
P
.AMP  
TUNER FILTER  
SPCH  
ATT  
M-CH/RIT  
SET  
[DIAL]  
[M-CH]  
U (USB)  
M-CH/RIT  
SET  
r Push  
to exit the set mode and return to  
normal operation.  
<CI-V system>  
Send the command “FE FE 76 E0 1A 03 24 03 FD”* to the transceiver.  
USB  
*The transceiver’s address is described as “76” and the controller’s address is described as “E0” for examples  
in this guide.  
17  
FOR YOUR REFERENCE  
About audio (Continued)  
USB level setting  
Set the input modulation level of the USB jack in the set mode item ‘USB Level’ or CI-V system (command).  
<Set mode>  
M-CH/RIT  
SET  
q Push and hold  
for 1 sec. twice to enter  
the set mode.  
w Rotate [M-CH] to select “USB LVL.”  
e Rotate [DIAL] to set the input modulation level of  
the USB jack within 0% to 100% in 1% steps.  
ANF  
METER  
NB NR  
1
1.8  
2
3.5  
3
7
V/M  
A/B  
=
SPLIT  
4
10  
5
14  
6
18  
MW  
M-CL  
AGC  
VOX  
COMP 7  
21  
8
24  
9
28  
SCAN  
.
0
50  
F-INP ENT  
BAND  
MODE  
TS  
RIT GENE MNF  
P
.AMP  
TUNER FILTER  
SPCH  
ATT  
M-CH/RIT  
SET  
[DIAL]  
[M-CH]  
50% (default)  
M-CH/RIT  
SET  
r Push  
to exit the set mode and return to  
normal operation.  
<CI-V system>  
Send the command “FE FE 76 E0 1A 03 25 0128 FD”* to the transceiver from the PC.  
Input modulation level  
• 0000 (0%) to 0255 (100%) can be set as the input modulation level.  
*The transceiver’s address is described as “76,the controller’s address is described as “E0” and input modula-  
tion level is described as “0128 (50%)” for examples in this guide.  
The modulation input audio format  
The modulation input audio format from the USB jack is listed as below.  
The number of data bit  
Sampling rate*  
16-bit  
Modulation input  
32/44.1/48 kHz  
The number of channel Monaural (Stereo: The audio signal from L is input.)  
* The sampling rate other than those above can be used according to the application.  
[Installed audio player] (Windows standard software, etc.)  
®
When using the audio software (e.g.Windows standard software; Microsoft Sound Recorder, etc.), the following  
operations can be performed;  
• Received audio output to the PC.  
• Modulation input from the PC.  
PC software (third party) is additionally required when the following operations are performed;  
• Monitoring the received audio with the speaker that is connected to the PC.  
• Modulation input for the PC microphone’s audio.  
18  
FOR YOUR REFERENCE (Continued)  
Specifications  
Connector type  
Interface  
USB B type  
USB 2.0/1.1  
Power supply  
Support OS  
Self power  
The PC cannot recognize the transceiver when the power is OFF.  
Windows Vista  
Windows XP  
Windows 2000  
Compliant for CI-V spec.  
Asynchronous serial  
Construction (1 bite)  
Start bit  
Serial for CI-V  
: 1  
Data bit  
: 8  
Parity bit  
: No  
Stop bit  
: 1  
Speed  
: 300/1200/4800/9600/19200 bps  
Received audio output  
Modulation input  
Number of data bit  
Sampling rate  
Number of channel  
Number of data bit  
Sampling rate  
Number of channel  
: 16-bit  
: 8/11.025/16/22.05/32/44.1/48 kHz  
: Monaural (Stereo: The same audio signals are output from both L/R.)  
: 16-bit  
: 32/44.1/48 kHz  
: Monaural (Stereo: The audio signal from L is input.)  
All stated specifications are subject to change without notice or obligation.  
A-6668-3EX © 2008 Icom Inc.  
19  

LG Electronics VX5200 User Manual
Keurig Vue V500 Brewer V500 User Manual
Kenwood KDC X915 KDC X815 KDC 9015 User Manual
Kenwood CD 324M User Manual
JMR electronic JMR Electronics Computer Accessories PUB 00281 User Manual
Centon electronic DataStick Bolt 8GBDSB BLUE User Manual
Bunn 37614 041410 User Manual
Blackberry Storm 9530 User Manual
Aiwa XP ER800N User Manual
Addonics Technologies CIPHERUSB CA256USB User Manual