Panasonic Network Card 2SB1722G User Manual

This product complies with the RoHS Directive (EU 2002/95/EC).  
Transistors  
2SB1722G  
Silicon PNP epitaxial planar type  
For high breakdown voltage low-frequency amplification  
Features  
Package  
Code  
SSMini3-F3  
Marking Symbol: 4R  
Pin Name  
1. Base  
High collector-emitter voltage (Base open) VCEO  
SS-Mini type package, allowing downsizing of the equipment and  
automatic insertion through the tape packing  
Absolute Maximum Ratings Ta = 25°C  
2. Emitter  
3. Collector  
Parameter  
Symbol  
Rating  
100  
100  
5  
Unit  
V
Collector-base voltage (Emitter open) VCBO  
Collector-emitter voltage (Base open) VCEO  
Emitter-base voltage (Collector open) VEBO  
V
V
Collector current  
IC  
ICP  
PC  
Tj  
20  
mA  
mA  
mW  
°C  
Peak collector current  
Collector power dissipation  
Junction temperature  
Storage temperature  
50  
125  
125  
Tstg  
55 to +125  
°C  
Electrical Characteristics Ta = 25°C 3°C  
Parameter  
Symbol  
VCBO  
VCEO  
VEBO  
ICBO  
Conditions  
Min  
100  
100  
5  
Typ  
Max  
Unit  
V
Collector-base voltage (Emitter open)  
Collector-emitter voltage (Base open)  
Emitter-base voltage (Collector open)  
Collector-base cutoff current (Emitter open)  
Collector-emitter cut-off current (Base open)  
Forward current transfer ratio  
IC = −10 µA, IE = 0  
IC = −1 mA, IB = 0  
V
IE = −10 µA, IC = 0  
VCB = −50 V, IE = 0  
VCE = −50 V, IB = 0  
VCE = −10 V, IC = −2 mA  
V
100  
1  
nA  
µA  
ICEO  
hFE  
200  
700  
Collector-emitter saturation voltage  
Transition frequency  
VCE(sat) IC = −10 mA, IB = −1 mA  
fT VCB = −5 V, IE = 2 mA, f = 200 MHz  
0.3  
V
200  
MHz  
Note) Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7030 measuring methods for transistors.  
Publication date: May 2007  
SJC00389AED  
1
 
This product complies with the RoHS Directive (EU 2002/95/EC).  
SSMini3-F3  
Unit: mm  
1.60 +00..0035  
0.26 +00..0025  
3
1
2
0.13 +00..0025  
(0.50)  
(0.50)  
1.00 0.05  
(5°)  
 
Request for your special attention and precautions in using the technical information and  
semiconductors described in this book  
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and  
regulations of the exporting country, especially, those with regard to security export control, must be observed.  
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples  
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other  
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other  
company which may arise as a result of the use of technical information described in this book.  
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office  
equipment, communications equipment, measuring instruments and household appliances).  
Consult our sales staff in advance for information on the following applications:  
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support  
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-  
ucts may directly jeopardize life or harm the human body.  
Any applications other than the standard applications intended.  
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-  
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product  
Standards in advance to make sure that the latest specifications satisfy your requirements.  
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions  
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute  
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any  
defect which may arise later in your equipment.  
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure  
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire  
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.  
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,  
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which  
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.  
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita  
Electric Industrial Co., Ltd.  
 

Miele Washer Dryer WTV 421 User Manual
Nikon Marine GPS System MC 35 User Manual
Nortel Networks Answering Machine P0908524 User Manual
Nortel Networks Network Card AN DC User Manual
Nortel Networks Switch 5625HD User Manual
NuTone Fan PFMB User Manual
Oregon Scientific Clock PS M03 User Manual
Oregon Scientific Thermometer RMR182 User Manual
Panasonic Air Compressor DC57C84RCU6 User Manual
Panasonic Universal Remote AJ RC5 User Manual