Oricom PMR888
UHF Two-Way Radios
Your Oricom PMR888 display
Keypad lock
Battery level
Duplex mode
Scan
Roger beep
CTCSS code
Channel
VOX
N13134
Complies with all relevant Australian and New Zealand approval requirements including radio communications
(Electronmagnetic Radiation Human Exposure) standard 2003.
2.
Safety and general information
This pack contains
PMR888
Exposure to Radio Frequency (RF) energy
• 2 UHF radios
• 2 Belt clips
• This user guide
Your radio contains both a receiver and transmitter.
When it is turned on it receives and transmits RF
energy. Your Oricom unit is designed to comply with
local regulatory requirements concerning exposure
of human beings to RF energy (Specific Absorption
Rate Data (SAR).
Attaching the belt clip (2 included)
Your radio comes with a swivel belt clip.
To attach, align belt clip post
with the hole in the back of
the radio and gently push
until it clicks into place.
Use and care
• This unit is not waterproof; do not immerse
it in water.
• If the unit gets wet turn it off, remove the batteries
and dry it with a soft cloth.
• Do not use it until it is completely dry.
To remove, push release tab
on top of the belt clip down
to release catch and pull belt
clip from the radio back.
3.
Installing the batteries
3. Insert the Ni-Mh battery pack
inside the battery compartment,
Each radio uses one Ni-Mh rechargeable battery
pack (not supplied). Or three AA alkaline batteries
(not supplied).
with charge contacts
towards you.
facing
Warnings
• Do not mix old and new batteries.
• Do not charge alkaline batteries they could
explode and cause injury.
4. Replace the battery cover.
1. Ensure radio is turned off.
2. Locate the clip on the back.
Use
your
fingernail
to
gently prise open the battery
cover.
charge contacts
clip
4.
others know you are finished talking.
1. To enable or disable the Roger beep, press and
Using your Oricom PMR888
hold
as you turn your radio on.
Turning your radio on and off
2. When the Roger beep is enabled
show in the display.
3. When you release the “PTT” button you will
hear the Roger beep.
will
Turn the volume button clockwise to turn your radio
on. The radio chirps and the display will briefly
show all feature icons that your radio has available.
Turn the volume button anticlockwise until it clicks
to turn your radio off.
Talking and listening
It is good radio etiquette to monitor the channel for
activity before you transmit, to ensure that you do
not interrupt other users already on the
channel.
Adjusting the volume level
Use the volume button to adjust your volume to a
comfortable listening level.
Selecting the channel
The channel is the frequency your radio uses to
transmit on.
Press and hold
to check for channel activity. If
you hear static, the channel is clear for use. Your
radio has 38 channels. If you are in a group and you
wish to talk to each other, all radios must be set to
the same channel and interference eliminator code
(CTCSS). If you experience interference and need
to change channel, ensure that you change the
channel and code of all radios in your group.
1. For maximum clarity, hold the radio 5 to 7 cm
from your mouth.
1. Press
flash.
and the channel number will begin to
2. Use
or to select the channel.
3. Press “PTT” to set a new channel.
Roger beep
When you turn on this feature, your two-way radio
transmits a unique tone when you finish transmitting.
In the same way as saying “Roger” or “over”, it lets
5.
2. Press and hold “PTT” and speak into the
microphone. The LED indicator light glows
continuously when transmitting.
display and the radio will scroll through the
channels.
5. When activity is detected on a channel, the
radio will stop scanning and you will hear
whatever transmissions are detected. The
radio’s display will show the channel and code
on which the activity was detected.
6. If you want to respond to the transmission,
press “PTT” within 5 seconds and you can
respond.
3. To receive messages, release “PTT”.
Note: If the PTT is held down for longer than 60
seconds a tone will be heard, the unit will stop
transmitting and return to standby mode.
Channel scan
By scanning, you can monitor channels and codes 7. The radio will resume scanning after 5 seconds
for transmission and lock in on the one that interests of inactivity on the channel.
you. More importantly, you can find someone in your 8. To stop scanning, briefly press and release
group who has accidentally changed channels and
.
is talking during your scan.
Interference eliminator codes
1. To start scanning, briefly press and release
2. If you activate scan while your code is set to 0,
.
Interference eliminator codes help to minimise
interference by providing you with a choice of code
the radio will check for any activity on combinations.
each channel, regardless of the code in use on
that channel.
1. Press twice and the code number begins to flash.
3. If you activate scan while the code is set on 1 2. Use the
or
button to change the code.
to 38, the radio will check for any activity 3. Press “PTT” to set a new code.
on each channel, except the code 0 in use on
that channel.
4. While the radio is scanning, the scan icon will
6.
You can specify a different code for each channel.
1. To set a channel and code combination, press
To restore the channel to the scan list, turn the radio
off and then on. You cannot remove your home
channel from the scan list (your home
channel is the channel your radio was set to when
you activated scan).
once
the channel.
2. Press again and then press
select a code.
and then press
or
to select
or to
3. The radio does not support interference
eliminator codes on channels 5 or 35. On these
channels press . The radio will skip the
code settings.
4. Press “PTT” to exit the menu and to save the
channel and code combination.
Monitor mode
This feature allows you to listen for weak signals on
the current channel.
1. Pressing and holding
your channel for activity.
2. Adjust volume up or down.
allows you to monitor
To set another channel and code combination,
repeat these steps.
Keypad lock
The keypad lock disables all the buttons. But allows
you to use the
Press and hold
keypad. When the radio is locked will appear in
the display.
button to monitor the channel.
for 3 seconds to lock or unlock the
Scan advance
If scan stops on a channel that you don’t want
to listen to, briefly press
scanning for the next active channel.
or
to resume
Sending a call tone
Nuisance delete
A call tone alerts others in your group that you want
to talk. Your radio has 10 call tones to choose from.
If scan continuously stops on an undesired
channel, press and hold or for at least 3
seconds, then release. This will temporarily remove
the undesired channel from the scan list.
7.
Select call tone
1. With the radio on, press
appears in the display.
the battery meter has one segment left, the radio
chirps after releasing “PTT” every 10 minutes.
three times until “C”
2. Current call tone setting will begin to flash.
3. Press or
Duplex mode
to change and hear the call Repeater stations re-transmit your signal over a
tones while the setting number is flashing.
4. Press “PTT” to set a new call tone.
5. To send a call tone press “CALL”.
wider area giving you extended range depending on
the location, height and availability of the local
repeater station.
Note: The Australian UHF CB Radio Standard Your Oricom radio supports duplex mode on
restricts tone calling to 3 seconds. This unit will only channels 1 - 8 only. In duplex mode, the units support
transmit for a maximum 3 seconds in any 60 seconds.
Note: The radio does not support the call tone feature
on channels 5 or 35.
the use of a repeater in your area. If the repeater
channel in your area is channel 1, when you are in
duplex mode the transmit channel will be channel 31.
Time-out timer
To enter duplex mode select your repeater
The time-out timer feature helps extend battery life channel number in your area (1-8) then press
by preventing accidental transmission. The radio will or on that channel until is displayed beside
emit a continuous warning tone after the “PTT” the channel number (1-8). You are now in repeater
button is pressed for 60 continuous seconds and mode.
will stop transmitting.
For more information on the locations of repeater
sites in Australia and New Zealand visit our website.
The battery level meter
The battery meter located in the display indicates
how much battery power you have remaining. When
8.
Channel
Frequency
Alerts
1*
2*
3*
4*
5*
6*
7*
8*
9
476.425 MHz
476.450 MHz
476.475 MHz
476.500 MHz
476.525 MHz
476.550 MHz
476.575 MHz
476.600 MHz
476.625 MHz
476.650 MHz
476.675 MHz
Channel busy indicator
The red LED will flash twice per second to indicate
that the channel is in use.
Call tone
Press the “CALL” button to transmit your call tone,
alerting users on the same channel and code that
you are about to talk. Your radio has 10 call tones
to choose from. Setting the call tone to 0 disables
this feature.
10
11
UHF Channels and frequencies
UHF Channels and frequencies
12
13
14
15
16
476.700 MHz
476.725 MHz
476.750 MHz
476.775 MHz
476.800 MHz
IMPORTANT NOTE
Channels 5 and 35 are emergency channels.
Channel 11 is a calling channel. Channels 22 and
23 are for Telemetry and Telecommand use, voice
communications are not allowed on these
channels by law.
17
18
19
20
21
476.825 MHz
476.850 MHz
476.875 MHz
476.900 MHz
476.925 MHz
9.
24
477.000 MHz
477.025 MHz
477.050 MHz
477.075 MHz
477.100 MHz
477.125 MHz
477.150 MHz
477.175 MHz
477.200 MHz
477.225 MHz
477.250 MHz
477.275 MHz
Using the optional value-plus
charge kit
25
26
Using the optional twin charging pod (not included)
27
28
29
30
31*
32*
33*
34*
35*
36*
37*
38*
39
477.300 MHz
477.325 MHz
477.350 MHz
477.375 MHz
477.400 MHz
Charging pod
To use the charging kit, place the charging pod on
any flat surface.
40
1. With the radio off, remove the battery cover.
2. Insert the Ni-Mh battery packs into the radios.
3. Replace the battery cover.
*Repeater access channels
4. Plug one end of the AC power adaptor into the
charging pod and then the plug pack adaptor
into the main power.
10.
5. Slide the radios into the charging pod ensuring
the charging contacts line up. The red light on
the charge kit glows when radios are properly
inserted.
6. The radios/batteries will be fully charged within
16 hours.
1 twin charging pod
Note:
When
moving
between
hot/cold
environments do not charge the battery until the
battery temperature acclimates (usually about 20
minutes).
Ordering the optional value-plus
Ordering the optional value-plus
charge kit
charge kit
The optional charging kit CHKIT888 can be
ordered directly from Oricom International.
1 AC power adaptor
The value-plus charge kit includes:
1 twin charging pod.
1 AC power adaptor
2 rechargeable Ni-Mh battery packs
2 VOX headsets
2 rechargeable Ni-Mh battery packs
11.
Warranty information
This product is covered by a 12-month warranty
against defective workmanship or parts. The
warranty does not extend to damage caused by
misuse, negligence, water ingress, battery
leakage or lightning. This guarantee in no way
affects your statutory rights. Full details of the
warranty are contained in the enclosed warranty
card.
2 VOX headsets
The kit is available at a cost of $59.00*
If you feel this product is not working correctly
please consult the user guide and ensure that you
are using the product in accordance with the
instructions.
Contact Oricom on:
Payment can be made by Mastercard, Bankcard
or Visa card.
For assistance with technical issues please
consult our website for further information or send
us an email for a prompt response to your enquiry.
In the unlikely event of a fault developing, please
contact us for assistance. If the product is then
found to be faulty you will be asked to return it
directly to us with a copy of the purchase receipt.
*Correct at time of printing (prices include gst and postage).
12.
Contact us
Australia
Oricom International Pty Ltd
Locked Bag 658
South Windsor NSW 2756
Australia
Customer support
Email: [email protected]
Fax: (02) 4574 8898
Phone: 1300 889 785
New Zealand
Atlas Gentech (NZ) Limited
Private Bag 14927
Panmure Auckland
New Zealand
Customer support
Email: [email protected]
Fax: (09) 574 2722
13.
Stay in touch for FREE with Oricom
Highly sophisticated: You can communicate when you’re around the home, out and about enjoying sport
and leisure activities or on a job site for free with the PMR888.
Long range: With 500mW of power you can expect up to 3km range depending on terrain and environmental
conditions.
Free communication: No call costs.
No license required: Start using your Oricom PMR888 radio straight away.
Highly compact: Lightweight and small, they easily fit in your pocket or bag, or clip them on your belt with
the clips included.
Smart features: Advanced features include 40 UHF channels, up to 12 hours talk-time, channel scan,
mechanical volume control and Roger beep confirmation tone.
Channel scan: Lets you easily find your group’s channel by searching all possible channels.
12-month warranty
Each pair requires a total of 6 AA batteries (not supplied).
KEM-PK10831-02
|