Oregon Scientific Clock MSR939A User Manual

POLERMO Projection Clock  
with Motion Alert  
Model: RMR939PA / MSR939A  
USER MANUAL  
RMR939PA English Cover R5  
1
9/21/04, 2:40 PM  
 
Notices .................................................................... 23  
Statement of Responsibility ................................. 23  
About Oregon Scientific ........................................ 23  
FCC Statement ....................................................... 24  
Declaration of Conformity .................................... 24  
INTRODUCTION  
Thank you for selecting the Oregon ScientificTM  
POLERMO Projection Clock with Motion Alert. This  
device is designed to give you many years of reliable  
service, including the following conveniences:  
US Atomic Calendar Clock  
Optional Wireless Vibration Alarm with 8-Minute  
Snooze Function (Wake-Up Vibrating Alarm  
VR101A can be purchased separately)  
Sleep Function with 6 Soothing Sounds  
5 Alarm Melodies with 2 Volume Levels  
2-Minute Dual Alarm with 8-Minute Snooze Function  
Time / Alarm Status Projection Unit  
Security Alarm / Motion Sensor Unit  
Indoor Temperature Display  
Day of the Week in 1 of 5 Languages  
Time Zone Hour Offset Function  
Backlight for Clock  
Keep this manual handy as you use your new product.  
It contains practical step-by-step instructions, as well  
as technical specifications and warnings you should  
know.  
2
RMR939PA English R5  
2
9/21/04, 2:40 PM  
 
PRODUCT OVERVIEW  
FRONT VIEW  
1
2
1. SOUND / SLEEP button  
Press to turn the soothing sound ON.  
Press to wrap around the sleep timer setting as  
follows: 0  
minutes.  
120  
90  
60  
30  
15  
3
0
Press and hold for 2 seconds to choose 1 of  
6 soothing sounds.  
6
7
2. SNOOZE / LIGHT button  
4
5
Press to activate the 8-minute snooze function.  
Press and hold for 2 seconds to turn snooze OFF  
and reset the alarm for the next day.  
8
Press to activate the backlight and projection for  
5 seconds.  
3. LCD display  
4. CLOCK ALARM button  
Press to toggle between alarm 1 and alarm 2 -  
ON / OFF.  
Press and hold for 2 seconds to enter the Alarm  
Time Setting Mode.  
5. MOTION ALARM button  
Press to enter the Motion Alarm Mode; press  
again to toggle between motion alarm ON / OFF.  
3
RMR939PA English R5  
3
9/21/04, 2:40 PM  
 
Press and hold for 2 seconds to enter:  
-
-
Motion Sensor Code.  
MotionAlarm Setting Mode for motion alarm  
period and alarm type.  
6. Projector  
Projects time and alarm status.  
7. CLOCK button  
Press to toggle between the following display  
modes:  
-
-
-
Clock with seconds and calendar.  
Clock with weekday and calendar.  
Clock with time zone hour offset and calendar.  
Press and hold for 2 seconds to enter the  
Clock Setting Mode - US time zone hour offset,  
12- / 24-hour format, hour, minute, year, MM / DD  
or DD / MM format, month, day and day of the  
week language.  
8.  
UP /  
DOWN button  
Press to increase or decrease a setting.  
Press and hold for 2 seconds to activate or  
deactivate atomic clock.  
Press to increase or decrease the soothing sound  
volume.  
4
RMR939PA English R5  
4
9/21/04, 2:40 PM  
 
BACK VIEW  
1. Projector FOCUS knob  
Twist to focus the projected image.  
2. Projector IMAGE ROTATION knob  
1
Twist to get the best viewing angle of the projected  
image.  
6
3. PROJECTION ON switch  
Slide to ON for continuous image projection when  
the AC power is connected.  
2
3
4
4. Projector 180° ROTATION button  
Press to rotate the image upside down.  
5
7
8
5. 6V AC / DC Power Socket  
6. Battery Compartment (cover on)  
Uses 4 x UM-3 / AA 1.5V batteries.  
7. RESET hole  
Insert a thin blunt instrument to return all values  
to the default settings.  
8. °C / °F switch  
Press to select between °C / °F display format.  
5
RMR939PA English R5  
5
9/21/04, 2:40 PM  
 
LCD DISPLAY  
1. SOUND  
1
2
10  
11  
Appears when the sleep function is activated.  
3
4
2. Battery Low icon  
5
6
Appears when the clock batteries are low or, no  
batteries are installed and only the AC adaptor is  
connected.  
12  
13  
7
8
3. Time  
14  
15  
HH / MM, 12- / 24-Hour, AM / PM.  
16  
4. ZONE  
17  
18  
19  
9
Appears when you are in the Time and Zone Hour  
Offset display.  
5. Channel 1 / 2  
Ch.1 or Ch.2 will appear when the related motion  
sensor is activated.  
6. Motion Alarm ON icon  
7. Calendar  
DD / MM / YY or MM / DD / YY.  
8. Temperature  
°C / °F.  
9. Atomic Clock Signal Reception icon  
Shows the strength of the reception signal.  
6
RMR939PA English R5  
6
9/21/04, 2:40 PM  
 
10. MIN  
Appears when the sleep function is activated.  
11. Time Zone Hour Offset / Day of the Week  
Offsets the atomic clock time setting when you  
are in a different time zone (+ / -23 hours).  
Name of day available in 1 of 5 languages.  
12. START  
Start time for the motion sensor to be activated.  
13. Alarm 1  
Indicator to show this is alarm 1.  
14. Alarm 1 / 2 Time  
Shows alarm times / AM or PM.  
15. Melody Alarm icon  
Shows when the clock alarm is set.  
16. Vibration Alarm icon (Wake-Up Vibration Alarm -  
optional item)  
Appears on the display when the vibrating alarm  
has been set.  
17. Alarm 2  
Indicator to show this is alarm 2.  
18. STOP  
Stop time for the motion sensor.  
19. Motion Alarm Settings icon  
7
RMR939PA English R5  
7
9/21/04, 2:40 PM  
 
REMOTE MOTION SENSOR (MSR939A) - FRONT VIEW  
1. Rotary Motion Sensor  
Detects motion and activates both alarms on the  
remote motion sensor and main clock units in  
accordance with the settings used.  
1
Twist the knob to direct the sensor to the position  
you want.  
2. ALARM SOUND ON / OFF switch  
Slide switch to ON - the sensor will sound the  
alarm if it detects movement.  
Slide switch to OFF - the alarm sound function  
will be turned off.  
5
2
3
3. POWER ON / OFF  
Slide to turn the motion sensor ON or OFF.  
4. 4.5V Adaptor Socket (adaptor not included)  
5. Motion Alarm Speaker  
4
6. LED Indicator  
6
8
RMR939PA English R5  
8
9/21/04, 2:40 PM  
 
REMOTE MOTION SENSOR (MSR939A) - BACK VIEW  
1. Wall Mount  
2. Battery Compartment (cover on)  
Uses 3 x UM-3 / AA 1.5V batteries.  
3. CHANNEL 1 / 2  
Slide to select either Channel 1 or Channel 2.  
4. CODE switch  
1
2
Slide to change the Code.  
5. RESET hole  
Insert a thin blunt instrument to return all values  
to the default settings.  
3
4
5
9
RMR939PA English R5  
9
9/21/04, 2:40 PM  
 
Keep your product away from hot, humid conditions  
or strong sunlight.  
SAFETY AND CARE  
SAFETY PRECAUTIONS  
Every effort has been made to ensure the highest  
standards of reliability for your clock with remote  
motion sensor. However, if something does go  
wrong, please do not try to repair it yourself - consult  
your supplier.  
Please observe the following safety precautions when  
setting up and using this product.  
LCD panel - The LCD panel is made of glass, and  
may break if the unit is dropped.  
Do not use your product outdoors in the rain, or  
handle it with wet hands - water can damage  
electrical equipment.  
Heat sources - Keep the product away from heat  
sources, such as radiators, stoves, heaters, and  
other heat-generating products.  
Water and moisture - Do not use the product in or  
near water or in high moisture areas, such as a  
bathroom.  
GETTING STARTED  
PACKAGE CONTENTS  
Power source - The product may be susceptible to  
power surges. It should be unplugged during severe  
storms or whenever you will be away for a long time.  
Only use the type of power source specified in this  
manual. Do not overload power strips and extension  
cords, as this can cause a fire hazard.  
When you unpack your clock with remote motion sensor,  
make sure you keep all the packing materials in a safe  
place, in case you need to later transport the device or  
return it for servicing.  
In the box, you will find:  
CARING FOR THIS PRODUCT  
Clock Unit  
To ensure you receive the maximum benefit from using  
this product, please observe the following guidelines.  
Remote Motion Sensor  
Do not clean any part of the product with benzene,  
thinner or other solvent chemicals - this may cause  
permanent damage that is not covered by the  
guarantee. When necessary, clean it with a damp  
cloth.  
4 x UM-3 / AA 1.5V Batteries for the Clock  
6V AC / DC Adaptor for the Clock  
3 x UM-3 / AA 1.5V Batteries for the Remote Motion  
Sensor  
10  
RMR939PA English R5  
10  
9/21/04, 2:40 PM  
 
To install the clock batteries:  
BATTERIES  
The clock uses:  
4 x UM-3 / AA 1.5V batteries.  
The motion sensor uses:  
3 x UM-3 / AA 1.5V batteries.  
The optional wake-up vibration alarm VR101A  
(not included in the package) uses:  
2 x UM-3 / AA 1.5V batteries.  
To install the motion sensor batteries:  
NOTE  
It is recommended that you use alkaline  
batteries with this product for longer performance.  
To install the batteries, simply insert them making sure  
they match the correct polarities (+ and -). For best  
results, install batteries in the motion sensor before the  
clock. Press RESET after each battery change.  
NOTE Do not use rechargeable batteries for the clock  
or remote motion sensor.  
11  
RMR939PA English R5  
11  
9/21/04, 2:40 PM  
 
The remote sensor jack can be inserted into the socket  
as shown below:  
shows on the clock display when batteries are low  
or when there are no batteries installed and only the  
adaptor is connected.  
The LED indicator on the motion sensor and vibration  
alarm will flash in red when the batteries are low.  
AC ADAPTOR  
The clock / projector and the motion sensor use 6V and  
4.5V AC / DC adaptors respectively. (Adaptor for the  
motion sensor is not included.)  
The clock AC adaptor socket is found on the bottom of  
the clock. The jack can be inserted into the socket as  
shown below:  
NOTE  
The motion sensor has a Power ON / OFF  
switch to help conserve energy. Use the AC adaptor  
when using the motion sensor for long periods of time.  
The batteries are a good power source for back-up use.  
ABOUT ATOMIC CLOCK RECEPTION  
This clock can automatically synchronize the date and  
time with an official time-keeping organization in  
Boulder, Colorado. The unit can pick up an atomic  
clock signal when it is within 932 miles (1500km) of  
these locations. For more information on the Atomic  
12  
RMR939PA English R5  
12  
9/21/04, 2:40 PM  
 
To turn the atomic clock signal reception OFF:  
NOTE  
For best results, place the clock away from metal  
or electrical objects, and near a window with a clear view  
to the sky.  
Press and hold the button for 2 seconds.  
The atomic clock reception icon will disappear from  
the display.  
TURNING THE ATOMIC CLOCK SIGNAL ON / OFF  
To turn the atomic clock signal reception ON:  
CLOCK / CALENDAR  
Press and hold the button for 2 seconds.  
CLOCK / CALENDAR DISPLAY  
The atomic clock reception icon will appear and flash  
on the display to indicate it is searching for the atomic  
clock signal.  
There are 3 types of clock display:  
Calendar /  
Clock / Sec  
Calendar /  
Clock / Day  
Calendar /  
Clock / Offset  
Once batteries have been installed in the clock, the  
reception icon will flash to indicate it is searching for a  
signal.  
When the reception signal has been received the  
reception icon will show the signal strength by displaying  
between 0 and 3 waves:  
Press the CLOCK button to toggle between the 3 types  
of display.  
Strong Signal  
Weak Signal  
No Signal  
13  
RMR939PA English R5  
13  
9/21/04, 2:40 PM  
 
6. Press CLOCK ALARM or MOTION ALARM to exit  
SETTING THE CLOCK / CALENDAR  
the Clock Setting Mode.  
Before you can manually set the clock and calendar,  
you must specify the current time zone you live in and  
the time format (12- or 24-hour) as follows:  
You can select 1 of the 5 following languages:  
SYMBOL  
LANGUAGE  
English  
1. Press and hold the CLOCK button for 2 seconds.  
The time zone offset hour digits will flash. The default  
setting will be -8 which stands for Pacific time. Select  
the following for different US time zones:  
German  
French  
-7 : Mountain time  
-6 : Central time  
-5 : Eastern time  
Italian  
Spanish  
BACKLIGHT  
Press SNOOZE / LIGHT to activate the backlight for  
5 seconds.  
TEMPERATURE  
2. Enter the value by pressing the or buttons.  
To choose between °C / °F, press the °C / °F button to  
select the setting you want.  
3. Confirm the entry by pressing the CLOCK button.  
The 12- or 24-hour display format will flash.  
4. Repeat (2) and confirm the entry by pressing the  
CLOCK button.  
5. Repeat the above procedures to set the hour, minute,  
year, MM / DD or DD / MM format, month, day and  
day of the week language.  
14  
RMR939PA English R5  
14  
9/21/04, 2:40 PM  
 
ACTIVATING / DEACTIVATING THE ALARM(S)  
ALARM  
Press the CLOCK ALARM button to toggle between  
alarm 1 and alarm 2 ON / OFF.  
ALARM DISPLAY  
The melody and vibration alarm icons indicate the daily  
alarm settings. Any disabled alarm will show no melody  
or vibration alarm icons.  
When the melody or vibration alarm icons appear  
on the display the alarm is activated. When the icons  
do not appear the alarm is deactivated.  
ALARM SOUND  
When activated, the alarm icon flashes, the backlight  
will come on for 8 seconds and the alarm melody or  
beep sound will play. If no key is pressed the alarm will  
play for 2 minutes.  
Alarm 2 (Wake-Up) Alarm 2 Melody  
+ Wake-Up  
Alarm 1 (Melody)  
Alarm 2 Disabled  
SETTING THE ALARM(S)  
NOTE See "Setting theAlarm(s)" section to choose the  
1. Press and hold CLOCK ALARM for 2 seconds to  
alarm melody / beep alarm and / or the vibration alarm.  
enter the Alarm Setting Mode.  
2. Alarm 1 will start flashing. Use the  
and  
SNOOZE / TURNING THE ALARM OFF  
buttons to toggle between alarm 1 and 2. Then press  
CLOCK ALARM to select alarm 1 or 2. The hour  
will start flashing.  
To silence the alarm:  
Press SNOOZE / LIGHT to silence it for 8 minutes.  
The alarm 1 or alarm 2 icon will flash to show snooze  
is enabled. Press and hold for 2 seconds to turn off  
snooze.  
3. Enter the value by pressing the or buttons.  
4. Confirm the entry by pressing the CLOCK ALARM  
button and move on to the next setting.  
5. Repeat (3 and 4) to set alarm 1 / alarm 2 - minute,  
melody alarm and / or vibration alarm (optional). If  
the melody alarm is selected, repeat (3 and 4) to  
select the melody / beep alarm sound and volume.  
OR  
Press any key except SNOOZE / LIGHT to mute the  
alarm and activate it again in 24 hours.  
6. The daily alarm will be on automatically after setting.  
Press CLOCK at any time to exit theAlarm Setting Mode.  
15  
RMR939PA English R5  
15  
9/21/04, 2:40 PM  
 
NOTE  
If no button is pressed, the alarm will  
SETTING THE MOTION ALARM  
automatically silence after 2 minutes. It will then sound  
again in 24 hours.  
The motion alarm has a security / monitoring function,  
whereby when the motion sensor detects movement, it  
sets off the clock alarm for 5 minutes and the backlight  
will turn on for 10 seconds. The clock will also show  
which sensor has been activated - Ch.1 or Ch.2 will  
appear in the top left hand corner of the display.  
MOTION ALARM  
MOTION ALARM SETTING DISPLAY  
The motion sensor icon indicates the motion alarm  
setting.  
You can set the motion alarm to be activated over a set  
period of time i.e. during night time, by entering values  
next to the Start / Stop Hour in the process detailed  
below. However, it is important that you set the Code on  
the clock display to match the Code on the back of the  
motion sensor(s) so that the items can interact with each  
other. This process is also detailed below.  
1
2
1. Press and hold MOTION ALARM for 2 seconds to  
enter the Motion Alarm Setting Mode.  
2. The Code will start flashing. Use the and buttons  
to choose the same Code setting as that displayed  
on the back of the motion sensor. Then press  
MOTION ALARM to select your chosen option. The  
start hour digits will start flashing.  
1. Code icon  
3. Enter the value by pressing the or buttons.  
2. Motion Sensor icon  
4. Confirm the entry by pressing the MOTION ALARM  
button and move on to the next setting.  
5. Repeat (3 and 4) to set the stop hour, beep / melody  
and volume.  
6. The motion alarm will be on automatically after setting.  
16  
RMR939PA English R5  
16  
9/21/04, 2:40 PM  
 
Press CLOCK or CLOCK ALARM at any time to exit  
the Motion Alarm Setting Mode.  
TURNING THE MOTION ALARM OFF  
Press any button on the clock to turn the motion alarm  
off. It will sound again when the remote motion sensor  
unit detects a motion again.  
SLEEP TIMER  
2. Press the SOUND / SLEEP button to set the sleep  
timer to turn off after 120 90 60 30 15  
You can choose 1 of 6 soothing sounds to play for a set  
time while you fall asleep:  
or 0 minutes. When 0 minutes is selected the  
soothing sound will automatically turn off after a few  
seconds.  
Bird  
Wind  
3. Use the or buttons to change the soothing sound  
volume.  
River  
4. SOUND will flash on the LCD display to indicate that  
Raindrop  
Waterfall  
Ocean Wave  
the sleep timer is activated.  
To select the soothing sound:  
To set the sleep timer and soothing sound volume:  
1. Press and hold the SOUND / SLEEP button for  
2 seconds when the soothing sound is on. The  
soothing sound number will flash.  
1. Press the SOUND / SLEEP button once. The  
soothing sound will turn on and the sleep timer will  
display the last setting.  
17  
RMR939PA English R5  
17  
9/21/04, 2:40 PM  
 
NOTE You can also press the SNOOZE / LIGHT button  
to project the time and alarm status for 5 seconds.  
MOTION SENSOR (MSR939A)  
The motion sensor has a security / monitoring function.  
It can set off your motion alarm on the clock for 5 minutes  
and turn the backlight on for 10 seconds when it detects  
movement.  
2. Use the  
or  
buttons to change the type of  
soothing sound.  
Data can be collected from up to 2 sensors. Additional  
sensor sold separately.  
3. Press the SOUND / SLEEP button to confirm the  
setting.  
SETUP SENSOR  
1. Slide the motion sensor battery door open.  
PROJECTION UNIT  
2. Insert the batteries, matching the polarity (+ and -)  
as shown in the battery compartment.  
The projection unit can display both time and alarm  
status. To use this feature:  
SWITCH  
Channel  
OPTION  
Channel 1-2. If you are using more  
than one sensor, select a different  
channel for each sensor.  
Slide the PROJECTION switch to ON to activate  
continuous projection. However, this function will not  
work unless the AC / DC adaptor is used.  
Adjust the FOCUS knob to make the image clearer.  
3. Set the channel by sliding the CHANNEL switch to  
1 or 2. The switch is located in the battery  
compartment.  
Adjust the IMAGE ROTATION knob to rotate the  
image clockwise or anti-clockwise.  
Manually tilt the projection unit to position the image  
or press the 180° ROTATION button to reverse the  
image and turn it upside down.  
4. Set the code by sliding the CODE switches to the  
same setting as the Code on the clock display. This  
enables the clock and motion sensor to interact with  
each other.  
18  
RMR939PA English R5  
18  
9/21/04, 2:40 PM  
 
5. Press the RESET button. Close the motion sensor  
You may need to experiment with various locations to  
get the best results.  
battery compartment.  
6. Secure the sensor in the desired location using the  
wall mount or table stand.  
7. Twist the motion sensor knob to direct the sensor to  
the position you want.  
WAKE-UP VIBRATION ALARM - VR101A  
(OPTIONAL)  
8. Slide the POWER ON / OFF switch to turn the motion  
The vibrating alarm receives a signal from the clock and  
performs a wake-up function by vibrating. It is designed  
to go under your pillow.  
sensor ON or OFF.  
9. Slide the ALARM SOUND ON / OFF switch to ON  
to activate the alarm sound function. The motion  
sensor alarm will now sound for 20 seconds if it  
detects movement. Slide to OFF to deactivate this  
function.  
The device has a range of roughly 50 feet and has an  
LED indicator to show data transmission and battery  
level.  
Once it has power, the motion sensor takes  
2 minutes to warm up.  
NOTE  
The switch within the vibrating alarm can adjust to  
alarm 1 or alarm 2, or both. Simply select the alarm time  
on the clock unit when you want the vibrating alarm to  
wake you up.  
For best results:  
Insert the batteries and select the channel before  
you mount the sensor.  
The vibrating alarm is powered by 2 x UM-3 /  
AA 1.5V batteries (included). It is also compatible with  
rechargeable batteries (not included).  
NOTE  
Place the sensor out of direct sunlight and moisture.  
Do not place the sensor more than 98 feet  
(30 meters) from the main (indoor) unit.  
Position the sensor so that it faces the main (indoor)  
unit, minimizing obstructions such as doors, walls,  
and furniture.  
RESETTING THE CLOCK  
Insert a thin blunt instrument into the hole below RESET  
to return to the default settings.  
Place the sensor in a location with a clear view to  
the sky, away from metallic or electronic objects.  
19  
RMR939PA English R5  
19  
9/21/04, 2:40 PM  
 
Do not tamper with the internal components.  
The default settings are:  
Do not mix new and old batteries or batteries of  
different types.  
Clock Time:  
12.00 PM  
Do not use rechargeable batteries with this product.  
Date:  
1st January 2004  
-8 (Pacific Time)  
6.00 AM  
Remove the batteries if storing this product for a long  
period of time.  
Time Offset:  
Alarm 1 and 2 Time:  
Alarm Melody:  
Daily Alarms:  
Do not scratch the LCD display.  
#1 with low volume  
Disabled  
The technical specification of this product and  
NOTE  
contents of this user manual are subject to change  
without notice. Images not drawn to scale.  
Motion Alarm Start Time:  
Motion Alarm Stop Time:  
Motion Alarm:  
12.00 AM  
6.00 AM  
Disabled  
Display Setting:  
12hr, MM / DD, °F  
TROUBLESHOOTING  
PROBLEM  
SYMPTOM  
REMEDY  
WARNINGS  
Clock time  
is not  
correctly  
set.  
No atomic  
clock  
signal  
Place the clock far  
away from PCs,  
phones, and other  
electronic equipment  
and near a  
This product is designed to give you years of service if  
handled properly. Oregon Scientific will not be  
responsible for any deviations in the usage of the device  
from those specified in the user instructions or any  
unapproved alterations or repairs of the product.  
Observe the following guidelines:  
reception.  
windowsill. Wait for  
at least 24 hours.  
Never immerse the product in water. This can cause  
electrical shock and damage the product.  
No alarm.  
Alarm does  
not sound.  
Turn on the alarm  
setting.  
Do not subject the product to extreme force, shock,  
or fluctuations in temperature or humidity.  
20  
RMR939PA English R5  
20  
9/21/04, 2:40 PM  
 
PROBLEM  
SYMPTOM  
REMEDY  
PROBLEM  
SYMPTOM  
REMEDY  
Operation  
not normal.  
Certain  
functions  
do not  
Reset the clock and  
the motion sensor.  
Motion  
Sensor.  
Does not  
activate the  
motion  
alarm on  
the clock.  
1. Adjust batteries /  
AC adaptor.  
2. Check POWER  
ON / OFF switch is  
set to ON.  
perform.  
Calendar.  
Clock.  
Strange  
day.  
Check it is set to  
your own language.  
3. Check the CODE  
switch on the  
motion sensor  
matches the clock  
code display.  
Cannot  
change  
clock.  
Disable the atomic  
clock signal and set  
manually.  
Clock /  
Calendar.  
Cannot  
auto-  
synchronize  
the clock.  
1. Adjust batteries.  
2. Press RESET on  
the clock and  
motion sensor.  
TECHNICAL SPECIFICATIONS  
Temperature. Shows  
"LLL" or  
Temperature is out of  
range.  
TYPE  
DESCRIPTION  
"HHH".  
Main Unit Dimensions  
L x W x H  
6.34 x 1.18 x 4.06 inches  
(161 x 30 x 103 mm)  
Motion  
Sensor.  
Does not  
give out  
alarm  
1. Adjust batteries /  
AC adaptor.  
2. Check POWER  
ON / OFF switch  
is set to ON.  
Weight (without battery) 0.59 lbs (268 g)  
sound.  
Remote Motion Sensor Dimensions  
L x W x H  
3.46 x 1.69 x 4.41 inches  
(88 x 43 x 112 mm)  
3. Check ALARM  
SOUND switch is  
set to ON.  
Weight (without battery) 0.31 lbs (140 g)  
21  
RMR939PA English R5  
21  
9/21/04, 2:40 PM  
 
TYPE  
DESCRIPTION  
TYPE  
DESCRIPTION  
Temperature  
Unit  
Hour Format  
Calendar  
12hr AM / PM or 24hr  
°F / °C  
DD / MM or MM / DD,  
user selectable. Weekday  
selection in 5 languages  
(E, D, F, I, S)  
32°F to +122°F  
(0°C to +50°C)  
Operating Range  
Indoor Range  
23°F to +122°F  
(-5°C to +50°C)  
Alarm  
Daily dual alarm  
2-minute crescendo  
8-minute snooze  
Resolution  
0.2°F (0.1°C)  
Main Unit Atomic Frequency  
Motion Alarm  
Atomic Clock  
WWVB60  
Frequency System  
Soundsfor5minutes  
Synchronization  
RF Frequency  
Auto or disabled  
433 MHz  
Power  
Main Unit  
4 x UM-3 (AA) 1.5V  
batteries or 6V AC  
adaptor  
Reception Range  
98 feet (30 meters) with  
no obstructions  
Remote Motion  
Sensor Unit  
3 x UM-3 (AA) 1.5V  
batteries or 4.5V AC  
adaptor (adaptor not  
included)  
Remote Unit  
Motion Sensor  
Coverage Distance  
Approx. 16 feet  
(5 meters)  
Motion Sensor Warm-  
Up Time  
Approx. 2 minutes after  
power-on  
Adaptor output current  
>=50mA  
Main Unit Display  
NOTE It is recommended that you use alkaline  
batteries with this product for longer performance.  
Clock  
HH:MM:SS  
HH:MM:Day of week  
HH:MM:Time zone  
hour offset  
NOTE Design and specifications are subject to change  
without notice.  
22  
RMR939PA English R5  
22  
9/21/04, 2:40 PM  
 
NOTICES  
ABOUT OREGON SCIENTIFIC  
STATEMENT OF RESPONSIBILITY  
more about Oregon Scientific products such as digital  
cameras; MP3 players; children's electronic learning  
products and games; projection clocks; health and  
fitness gear; weather stations; and digital and conference  
phones. The website also includes contact information  
for our customer care department in case you need to  
reach us, as well as frequently asked questions and  
customer downloads.  
Oregon Scientific will not be held liable for any bodily  
injury, death, property damages, or any other claims of  
whatever nature resulting from the misuse or negligence  
of the product, whether intentional or unintentional.  
Oregon Scientific will not be responsible for any  
deviations in the usage of the device from those specified  
in the user instructions or any approved alternations or  
repairs of the product.  
We hope you will find all the information you need on  
our website, however if you'd like to contact the Oregon  
Scientific Customer Care department directly, please  
visit:  
www2.oregonscientific.com/service/support  
OR  
Call 949-608-2848 in the US.  
For international enquiries, please visit:  
www2.oregonscientific.com/about/international/  
default.asp  
23  
RMR939PA English R5  
23  
9/21/04, 2:40 PM  
 
DECLARATION OF CONFORMITY  
FCC STATEMENT  
The information below is not to be used as contact for  
support or sales. Please call our customer service number  
the warranty card for this product) for all inquiries instead.  
This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant to  
Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful  
interference in a residential installation. This equipment  
generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio  
communications.  
We  
Name:  
Oregon Scientific, Inc.  
Address:  
19861 SW 95th Place, Tualatin,  
Oregon 97062 USA  
However, there is no guarantee that interference will not  
occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception,  
which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
declare that the product  
Product No.:  
RMR939PA  
Product Name: POLERMO Projection Clock with  
Motion Alert  
Manufacturer:  
Address:  
IDT Technology Limited  
Block C, 9/F, Kaiser Estate,  
Reorient or relocate the receiving antenna.  
Phase 1, 41 Man Yue St.,  
Hung Hom, Kowloon,  
Increase the separation between the equipment and  
receiver.  
Hong Kong  
Connect the equipment into an outlet on a circuit  
different from that to which the receiver is connected.  
is in conformity with Part 15 of the FCC Rules. Operation  
is subject to the following two conditions:  
Consult the dealer of an experienced radio/TV  
technician for help.  
1. This device may not cause harmful interference.  
WARNING Changes or modifications not expressly  
approved by Oregon Scientific for compliance could void  
the warranty and your authority to use this equipment.  
2. This device must accept any interference received,  
including interference that may cause undesired  
operation.  
24  
RMR939PA English R5  
24  
9/21/04, 2:40 PM  
 
© 2004 Oregon Scientific. All rights reserved.  
P/N: 000-000000-000  
RMR939PA English Back R5  
1
9/21/04, 2:40 PM  
 

Miele Ventilation Hood 09 813 750 User Manual
National Instruments Network Card NI USB 9219 User Manual
NEC Home Theater System NP60J User Manual
NEC Projector MT830 User Manual
NEC Projector MT 1020 User Manual
Nilfisk ALTO Vacuum Cleaner 30 BATT PC XC User Manual
NordicTrack Home Gym NTC05940 User Manual
P3 International Home Safety Product P7050 User Manual
Packard Bell Personal Computer REFDOCS02420200 User Manual
Panasonic Oven KX TDA100 User Manual